Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
Hi I am new to NRF52832. I am using SDK 16, Multlink Central (ble_app_multilink_central).
Here are my questions:
1) The software keep resetting when I flashed the code...
Setup nRF52840 DK S140 nRF52 SDK v16.0.0 nRF SDK for Mesh v4.0.0 Goal I would like to be able to disable the Mesh stack and all radio operations so that my application can...
Hi,
[Softdevice 6.1.1]
I am developing an application which uses the radio timeslot api in conjunction with BLE. Even without starting BLE advertising, or any other BLE...
I did some evaluation on nrf9160dk recently. I try to run some at command to control lte modem, but some wired thing happen.
After I introduce at command in to one work...
Is there is an option to change the payload of NFC t2t after setting the payload.
So the requirement is once there is a polling device is in the field, we need to change...
In ble_app_blinky_pca10040e_s112 example, Generic access service has read and write permission.
When writing the name, I want to handle this event and change the advertisement...
Hi Team,
We are using nRF52840 DK with the latest SDK 16.0.0. We know that SDK have multiprotocol support for BLE+thread and BLE+zigbee. Its okay for that and we tested...
Hi, i have been trying to get GPS and HTTP to be able to work with eachother, but im having some struggles.
After the GPS starts, the program begins spewing out "Invalid...
Hello,
I have exercised the flash driver and that is working fine. I want to save a certain value into a specific address in NVM and I want that part of the .hex file. I...
I just upgraded to SES 4.42 from 4.30a and I'm getting the following compiler warning for file zigbee_cli_cmd_ado.c "Taking address of packed member of struct zb_af_simple_decs_1_1_s...
Dear Sirs,
I am using example anr_hrm nrf_sdk_15.3.0 I would like to use PINs on/off
software s212
#include "nrf.h"
#include "nrf_gpio.h"
#include "nrf_delay.h"...
Dear All,
I am using (nRF52840) in one of my design.
Application program we have taken examples\peripheral\usbd_ble_uart\pca10056\s140\arm5_no_packs code as base code...
Hi,
Good Day!
Statement of Problem: We are using SPI to transfer data to custom LED matrix which uses HT1632C led driver. For strings more than 7 character length we used...
I want to integrate nrf mesh serial example in light Switch example to configure other un-provisioned node
I am using following nrf SDK: >> nrf : nRF5_SDK_15.2.0_9412b96...
Hello,
We have evaluated Smart Remote 3 example code .We migrated that code in the segger embedded studio but we are getting lots of error related to files and libraries...
