Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
Hi, i am trying to build a ble beacon for personal asset tracking. The one that is like Tile or Trackr. What kind of chipset and program that i should use.
Hello
P airing: Just Works with Bonding: Passkey Entry, Peripheral Displays works for bonding.
I want to make LESC Pairing: Just Works with Bonding. Is it possible? According...
I got a vague "cmake did not complete" error from studio when the sdk was installed at a hgfs mounted disk. It worked ok when the sdl was installed at non-mounted directory...
the gy-80 module which has
1. HMC5883L
2. BMP-085
3. L3G4200D
4.ADXL345
i want to get the x, y, z axis of the sensor's position
which example i have to use and...
I am building a project with CMake, inside nRF SDK for Mesh 3.2.0, which uses the math library:
1. source file includes math.h
2. CMakeLists.txt adds m to target_link_libraries...
There are a lot of missing materials under the topic:
Software Development Kit > Previous versions of nRF5 SDK for Thread and Zigbee > nRF5 SDK for Thread and Zigbee v3...
I'm converting an already working LPN that went into SystemOFF with GPIO wakeup for lowest power consumption.
Now I want to use the RTC2 as a secondary wakeup.
I know...
I am currently developing on the nrf52840DK (Rev 1.1.1) using the mbed os.
To debug on the board using OpenOCD it is necessary to flash the JLink firmware for the board...
Dear Nordic community,
we as a company, have developed products with the nRF52832... currently, we're developing a product with the nRF52840 (because we needed USB).
My...
Hello
I would like to change the Tx_Power using softdevice.
The sd_ble_gap_tx_power_set command shows me the supported tx_power values as -40dBm, -20dBm, -16dBm, -12dBm...
I have make some custom board with the same layout as a BMD-300 evaluation board (pca10040) with the same MCU which is used on this evaluation board from RIGADO. This is BMD...
Hiya,
We're running a few experiments with a wireless-mesh protocol based on rapid flooding on a few nrf52833 dev kits.
We'd ideally like to use a channel contention mechanism...
Hi, I am working on nRF9160DK lte_ble_gateway sample, in that I want to scan for beacons UUID and major, minor value. nRF52 device is programmed with bluetooth HCI (UART)...
I have a custom board uses nRF52810. When I flash my board with examples include SoftDevice (sdk 16.0.0) nRF52810 restarts. I am debugging with oscillascop and seeing that...
Hello,
what is the realistic maximum speed achievable over RTT on the 52840dk (using SEGGER_RTT_printf) to RTT Logger?
I have tried modifying frequency and NRF_LOG_BACKEND_RTT_TEMP_BUFFER_SIZE...
