Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi,
I am new here and I have some issues with Zigbee reporting implementation.
I am trying to implement a reporting feature between a coordinator and an end device, which...
Hi,
Attached is Cmake error log from one of the failed builds.
This is a new MBP with freshly installed nRF Connect - following tutorial.
Anyway, I am not able to open...
Hi all,
since new version of IOS nRF Mesh App I can't finish provisioning of my nRF52840 DK with flashed light example client.
When I start provisioning for the device...
Hi,
I am using NRF52832 with SDK 15.3 and SD 132 on our custom board ( VDD 1.96V ). I started with with the ble_app_template example for our application. Upon measuring...
Hi Nordic
I am using saadc example now, my device output voltage range is -4v~4v.
my saadc config:
VDD: 3.3V
Reference: VDD/4
Gain: 1/4
Mode: SINGLE_ENDE
i got...
Hi, I am new to BLE, I am trying to send and receive data over BLE and print them in Uart as well in both devices respectively.
And I downloaded lastest NRF5-SDK, I have...
Could you, please, direct me to any example (if available) how to manage lost bond with nRF52832/ SDK16 BLE?
Let say very common situation that will try to demonstrate with...
Hi all,
I have hardware as below:
nRF52840-DK - as an advertiser and the same type of board nRF52840-DK - as a scanner
My problem is that I want to send more data than...
Hi,
I have been going through the Bluetooth Course ( https://github.com/NordicPlayground/nRF52-Bluetooth-Course ) and I can' seem to make it work, even if copy/paste the...
Hi,
I'm using nRF51822 to develop our products. I found an interesting problem on our PCB. After I disconnected our PCB from central device, the main function starts from...
I am developing a wearable using nRF52832. I am using SKD_15.3 ble_app_uart source code for testing. And use Putty together. This source code implements UART Baudrate up to...
I have been using fds for flash saving and read. I have used fds_record_write(..) with no errors and proper readings on the just before performing a 4th fds_record_write(...
I'm currently investigating nRF Connect SDK. The nRF5 SDK (15.3.0) has a function to notify the advertise scan reception channel, but the current nRF Connect SDK does not...
