Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
We would like to develop an indoor navigation with BLE. The goal is to get the position of the mobile device and navigate to a specific location.
We have already four nRFBeacon...
Hi,
It looks like the nRF Mesh App on Android configures incorrect CCCD when an unprovisioned device exposes both Provisioning and Proxy Service in its GATT Database.
...
Is it possible somehow(and if it is then how) to send/receive user data from/to a PC terminal (serial port) to/from the dongle 52840 via nRF Connect of another provided s...
I'm trying to completely understand extended advertisements and what is possible when initiating a connection to a device advertising using extended advertisements. I'm using...
Hi,
is it possible that there is a mistake in the infocenter documentation of SDK v.15?
In the bootloader description under MemoryLayout:
Usage
Memory range...
I have recently downloaded nRF5_SDK_15.0.0_a53641a and tried to compile and run the ble_app_hrs on the nRF52 Dev Kit. I am using IAR-EWARM v8.30.1. The Soft Device is s132_nrf52_2...
RE: nrf52840QIAA - Can you recommend circuitry necessary to switch source between the usb and LiP battery? Can you recommend inexpensive/small footprint boost circuitry to...
Hello,
I control buzzer using below API.
I want to know the maximum value of period_in_us .
Thanks.
******************************************************...
Hi, I am using nRF52840-DK; Window 10; Embedded Studio and try to run sample project: C:\Nordic_Semi\nRF5_SDK_15.0.0_a53641a\examples\peripheral\cli\pca10056\blank\ses
I...
Hi,
I use STM32F103 as a receiver.
I read FIFO STATUS and STATUS register then execute FLUSH_RX command through SPI.
I continuously read FIFO_STATUS and STATUS registers...
Hi,
I asked previously about power efficiency for the NRF52840 SDK version V15 ( https://devzone.nordicsemi.com/f/nordic-q-a/36083/maximal-power-efficiency-in-main-loop...
I have an idea to open the source code of my personal project, since some source code of SDK are used and modified, is it OK to include the modified SDK source code in the...
I am using nrf52 developmemt kit. I am using mpu9250. the odr of mpu is 100 Hz. i am able to send data over ble using example code nrf5-ble-mpu-data-ready-interrupts . Now...
I' m using the nRF51 Dongle (PCA10031) for the evaluation of the OTA DFU bootloaders of SDK15.0.0 with the NRF52840 PDK. Using the PC tool nRFConnect V2.3.2 with the App Bluetooth...
