Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
I am working on a project of throughput data from sensors to my central via nrf52832 through a notifying service (SDK14.0.0, S132).
As explained in several questions...
In the Infocenter, there is a section about adding support for custom boards. It advises the creation of custom_board.h modeled after pca10040.h. However, the configuration...
I am starting a nRF52832 project that is based on the GCC + Makefile build system that is provided with the example projects. In my particular case, I need to execute a python...
Hello, everyone~
I'm trying to use mac to develop nRF52832 DK. I have installed the lastest J-Link driver and SES. I downloaded nRF5 SDK 14.2.0 and just open ble_hrs project...
I get nrf mesh SDK form: http://www.nordicsemi.com/eng/Products/Bluetooth-low-energy/nRF5-SDK-for-Mesh/(language)/eng-GB
I want to use the serial example to control a mesh...
I use the advertisement timeout to shut down the MCU. Is is possible to reset the advertisement timeout on the fly, e.g. if there is any activity I would like to extend the...
Hi,
I'm interfacing acceleration via BLE using NRF52.
I'm using timer to get the sensor value and update the characteristic value related to this sensor using sd_ble_gatts_hvx...
Hi,
I tried to make a software update (I tried application, bootloader, SoftDevice and any combinations) over BLE using the secure_dfu_ble_s132_pca10040 example but after...
Hello. I have a problem. After using nfc, current consumtion still high. I found that I need use HAL_NFC_ENGINEERING_A_FTPAN_WORKAROUND macros. But when I specify this macros...
Hi All,
I am going to get EMI/EMC testing for my custom board made on nRF52832 WLCSP package. Can you please share/suggest the firmware used in EMI/EMC testing.
hi everyone
i want use s130 with my ble nrf1822 i'm wondering about the modifiaction that i have to do under keil 5 in option for target for example the configuration that...
Hi,
I try to use the dfu update OTA with ble secure bootloader.
If the Flash is erased and only the SD v5.0.0 and the own Bootloader are programmed a update OTA is working...
When making a bluetooth mesh network, what is a good rule of thump for the ratio between servers and clients?
I am thinking of implementing the server-client-model scheme...
Hi Engineers!
We used SDK13 for our Project (multilink BLE with 1xServer & 4x PeerS) and now move to SDK14.2, almost done except only USBD.
if we use SDK13 driver...
