after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I've sifted through the examples given to me, and none of them seem to explain how to create your own service and add it to the stack. All of the services that are registered...
Hello,
I am working with the nRF-SDK-for-Mesh v0.10.1 I am able to compile and run everything fine. However the DFU example hangs. It looks like a hard fault ( all the...
Dear friends,
As shown in the pic below, my nRF connect won't start. Automatic firmware detection and programming are done.
nRF Connect: v2.2.1, board: PCA10040 AND PCA10036...
When i klick "Erase all" in nRFgo Studio, i allways get this Message
"unable to find or open JLinkARM.dll"
i did already try several hints from this site.
corrected...
Hello,
I will post this question to NDZ first time .
Our customer is in trouble to reduce power consumption at nRF52832.
Our enviornment is below.
CPU: nRF52832...
I am using the ble_app_uart example as my base on a 52840 with sdk 14.1. I have commented out BLE_ADV_EVT_IDLE case in on_adv_evt() function and the BSP_EVENT_SLEEP case in...
Hi:
I download the google official example "android-BluetoothLeGatt" from github
In the original code, the SDK26 is used, but it can not find any BLE device.
If the...
hi, i'm newbee in BLE,now i have a trouble about advertising in NRF51822.
in my project,after BLE disconnect, I can't see BLE again that mean BLE can't advertising continuously...
Is there a good Mac log analyzer for Android's btsnoop_HCI.log file?
I'm trying to debug an Error 0x81 (GATT_INTERNAL_ERROR) that is being returned when I try to write...
Hi, all!
Sorry, I'm not good at English myself.
My device is nrf52832.
Example code is ble_app_uart (pca10040, s132), I did not modify the code.
My problem.
Ble...
I'm working on a custom board based on the nRF52832. I'm developing on Win 8.1 using SES and a J-Link Plus. SDK version 14.1.
I'm trying to follow this tutorial here devzone...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
