Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
I have configured the nRF52832 as a GAP peripheral and wish to establish multiple concurrent connections between this and GAP central devices (Phones). Is this possible? What...
Hi,
my current project needs an i2c slave eeprom emulation like it is in the example projects of the sdk. The difference is that I need a larger packagesize of one transmission...
I want send out 6 notification in one connection interval. But now I only see 3 packets in my sniffer. So I want to know how to achieve this goal?
This picture is captured...
I'm using nRF51(822) with S130.
I registered my event handler with:
softdevice_ble_evt_handler_set(ble_evt_dispatch);
In my main loop, I call sd_app_evt_wait(); ...
Dear,all
device:51822 s110 sdk8.1.0 adverting interval:1s
or exmaple hrm s110 PCA10005
i use moto Z phone and nrf connect apk,it is difficult to receive
the advertise...
Hi, I have created a custom PCB (FR4, 4-layered) which uses nRF52832-QFAA.
This PCB uses the λ/4 printed monopole antenna .
I wish to measure the RSSI value of this...
hi,all
i use sniffer.exe(ble-sniffer_win_1.0.1_1111_Sniffer),and sniffer connection data,the sniffer.exe often automatically quit.
the sniffer pcb is not nordic.
anormal...
Hi,
Instead of initiating the DFU library in Android with an address is it possible to handover a existing GATT connection to a device already in DFU mode?
We have cases...
Hi,
I try to add support of dfu in our appl. In documentation I could not find info about softdevice size which should be provided in start packet. It looks like I should...
Hi,all
SDK:8.1.0 51822
S7 Edge（android V7.0）
i use the sumsung S7 Edge and the oppo R9S connect with my device,nRF Connect is often note:
GATT_CONN_TERMINATE_LOCAL_HOST...
for ble_app_ancs_c_s130_pca10028 example of sdk11,s130 version 2.0.0
The preferred RAM,ROM and UUID COUNT is shown below
FLASH (rx) : ORIGIN = 0x0001B000, LENGTH = 0x25000...
Hi All
I am trying to build hex file using eclipse id on Mac. everything looks ok, as it eclipse build file without any error but its not working on nrf52 dk.
before...
Now I’m using nRF51822 with S130 SoftDevice.
There are two kinds of devices which is just for scan(A) – 20EA and both scan and advertising(B) - 2EA.
I found that B just...
Hi,
My question is similar to this devzone.nordicsemi.com/.../ but I can't get it to work.
I am using SEGGER_RTT_WriteString and sprintf for debugging, but I am not able...
