If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
Hello
I'm trying to add zigbee to an existing freeRTOS project with BLE. The approach so far is combining "Zigbee Multi Sensor with FreeRTOS Example" and "Adding dynamic...
Hi.
I am writing software for my custom nRF52832 device but hardware wise it is identical to the nRF52 DK.
I'm not that good of an embedded coder (or any kind of coder...
Hello
In my application (based on ble_thread_dyn_mtd_coap_cli example), I would like to get the list of devices present on the network (ip).
I saw that there was a command...
Dear all,
My CMW500 have NB-IOT option only (NO CAT-M option is installed) and I would like to see how to setup CMW500 (NB-IOT mode ONLY) to communicate with Thingy91DK...
We are using Enhanced Shockbust and would like to maximize the operating range. We noticed this footnote on page 356 of the latest spec sheet (v1.1):
Typical sensitivity...
Hi,
I'm trying to reduce latency when relaying BLE packets. The goal is to have a couple of wireless peripherals connected to a hub talking BLE with a central, with minimal...
Hi,
I am trying to implement LC server for my lights. I want to make the RUN level of the LC model configurable i.e, change the RUN level according to the user need.
Can...
There was an unexpected issue configuring beacon ad packages. The task is to transfer as much data as possible in beacon mode. For this, I want to include the scan responce...
The chip we use is nrf52832 and the SDK is nrf5_ SDK_ 15.3.0_ 59ac345, Can we use nrf Toolbox (version: 2.7.2) to upgrade bootloader? 1. How to make bootloader upgrade package...
hi,
I have nrf52840 DK and a dongle and I would like to connect the dongle to android device and scan for the DK in coded phy.
where can I find some SDK for using the...
Hi,
From previous case , I still not fully understand how chip to retrieve the calibrated data from flash(already implemented read/write data for the interface by FDS),...
This question stems from this discussion
https://devzone.nordicsemi.com/f/nordic-q-a/71044/notifications-how-to-know-who-is-consuming-tx-buffers-most-efficient-way-of-sending...
The ARM Cortex-M4 supports many assembly-level DSP instructions and we would like to use them (not just the packaged ones in the CMSIS DSP libraries).
For example the set...
Hi All,
I want to use DFU to update the firmware from master to peripheral over BLE , both master and peripheral are nrf52840. My purpose is that the master sends a command...
Dear all:
My problem is described in the following steps：
1. Progranm the SoftDevice 7 (S132) into NRF52832, then program the ble_hid_keyboard example(SDK16) into NRF52832...
