after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I'm attempting to perform DFU with the secure bootloader (bonding not required) and it is hanging after starting the update. Here's the log from the firmware (SDK 16.0.0)...
Hello,
I am developing an app which connect to provisioned node using GATT in the mesh network. But the limitation of this is, it has only pair to pair communication. It...
Been beating my head against this for a couple of days and came across a number of people on the forum with the same issue without a solution, so hopefully this saves someone...
Hi all,
I have some issue setting up the advertising data on my nRF52840 Dongle. I'm using the ble_template to develop my software and in my application i need to fill all...
Hi all,
can i send a scan request from an nRF52840 dongle using the nRF Connect - Bluetooth Low Energy software? I need this during development of my application where i...
Hi
I am seing framing errors when receiving using UARTE.
It is not external hardware, I have checked with different other interfaces and measured timing, no problems there...
Hi
I want to ask a few question.
When the phone sends a specific signal after connecting to the MCU, the MCU is sending data in real time.
When the power is turned...
Hi,
I was trying to find out if it is available to have authentification before connection and I found this link and it makes sense to me but that Q&A has been over 4 years...
Hello!
I use Zigbee CLI example and multi_sensor example on nRF52840. (examples/zigbee/experimental/cli/cli_agent_router and examples/zigbee/experimental/multi_sensor) ...
I have nrf52840 dongle and sdk nRF5_SDK_17.0.0_9d13099.
I would like to know, is there is an example in which, Advertisement Data is stored in flash memory and reading and...
I USE 9160 with i2c ，send data. then it tips :
[00:02:07.716,918] [1;31m<err> i2c_nrfx_twim: Error 195952641 occurred for message 0[0m
what is wrong ?help me ,thank...
NOTE: This is related to the following issue: https://devzone.nordicsemi.com/f/nordic-q-a/63255/nrf9160-getting-stuck-after-cell-change
--------------------------------...
Hi,
I would like to read data from sensor and send it over BLE to nRF connect. Unfortunaly, something went wrong while reading the data by TWIM.
I´m using SDK16. ...
Hi Sir or Madam,
I tested examples\zigbee\light_control demo recently and I want to test install code function based on this example, the first step is I add install code...
