Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
We are using nrf51422 in our project.So right now i am loading the program using the Usb cable .Here my doubt is can we able to flash the program by using usb to uart...
Hello. It is almost the same as the question ( devzone.nordicsemi.com/.../set-data-type-for-notify) given three days ago. I want to “Notify” new data in the “rscs” project...
does FDS have append data functions? I want to receive big files(>500KB) from BLE,but I can put it into RAM buffer, so can I create a file in FDS and append it from BLE directly...
Hello Recently I have been working on a project for a 52832+ three-axis accelerometer. I have encountered some problems. SDK15.2 IIC 1.started a timer and it was time to collect...
Hi all,
I’m currently working with the nrf9160 sip on a bare metal firmware project. I know the official support path is only with Zephyr OS but I’m facing an issue I’m...
I modified my nRF52840 dongle as is was described here Does anybody have a single diagram showing how to connect the DK's P20 pinout to the dongle ? Thanks,
Matthew
Hello! On 2019-06-24 the following mail was received:
Product update notification June 24, 2019
Hi Bojan,
We've just released a new version of our SoftDevices, version...
To the kind attention of Nordic support team,
Could you please give a very quick look at those attached gerber files? Do you think there is something that is better to correct...
Hi Nordic team support,
I want to test communication range between nRF528xx device that support LE coded with samsung galaxy s10 (support LE coded also)
1. If I configure...
For some reason I can't quite program the nRF9160 on the development board using Segger Embedded Studio (SES) when I create a new project. I must be doing something wrong...
When I set "report_incomplete_evts = 1", I get a NRF_ERROR_NOT_SUPPORTED (0x06) error.
If I comment it out, everything work as expected. I want to use it for exended advertise...
Hi All,
I need to find the RF Tx power setting of the nRF52840 by reading from the register. I understand this is possible through Jlink and the following command:
--memrd...
Hello,
I am developping a project on with the nRF9160 and I would like to have the LTE and GPS working concurently. I managed to have both working separatelly on my custom...
Hi. I am confused about flash endurance. In the product specification for the nRF52832, there is a note that flash endurance is 10000 write/erase cycles:
Does it mean...
Hi,
What's the easiest way to subscribe to the MQTT messages that the thingy91 sends to the nRF cloud?
I have tried setting it up with a node-red and a python client...
