Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello All
I am planning to install the nRF51822 beacon, wanted to know how to setup so that the beacon broadcasts repeated eddystone based advertisement URL/ packets to...
I am trying to get the nRF24L01+ working with a PSoC 3.
I initialize the nRF like this..
spiWrite1(NRF_CONFIG, 0x0F); // reflect TX_DS, RX_DR and MAX_RT interrupts as...
I have installed this software several times without any result on PC.
How to access an IDE???
I am really very frustrated. Since several weeks I am not able to edit, compile...
When an interrupt with a printf in it triggers while another printf is still occuring the previous message is cutoff to print the next one.
Is there a way I can wait for...
Hi,
I've a custom board which has NRF51822 SOC and STM32 SOC. These two are connected over UART. In past I've successfully performed DFU OTA (BLE) for nrf51822 MCU, and...
I have got a Raytac module MDBT40(nRF51822) and development board nRF52832. Now I want to program the module using the development board. I have followed this video ( Programming...
Hello all,
I am trying to update my firmware using BLE peripheral.
I followed the instructions in this [tutorial] ( devzone.nordicsemi.com/.../)
I downloaded the SoftDevice...
Hello Nordic Forum!
Our product relies heavily in the TWI Bus, we use it to communicate with different sensors periodically. The most "important" one is read once every...
Hi,
We have made a custom board using the NRF52832 chip. The device is in hard fault mode and we believe it may be because of the corruption in internal memory. We wanted...
Hi,
Currently I am trying to test DCDC mode on my custom board nrf52832. After soldering 15nH and 10uH on DCC(pin 47), I issued the following command after softdevice enabled...
@Vidar: I have followed your steps in tutorial for "Development with GCC and Eclipse" and when I try to flash my device I get the below error
Nrfjprog.exe is not being...
Like many others (read a lot of threads here about this and also beneath the tutorial to Eclipse many people write that they suffer for it) i have problems in Eclipse with...
Hi,
I'm using the example dfu/bootloader_secure_ble for NRF52832 (PCA10040 board) in nRF SDK 13.0.0 version and on my mobile the "nRF Connect" application.
If I use...
Hello,
I'm working on a project based on the ble_app_multirole_lesc example, under examples/ble_central_and_peripheral/experimental and I found a bug.
In ble_evt_dispatch...
