Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Some situations like heavy ble activity causes the nrf52832 to restart without hitting breakpoints in the NVIC_SystemReset.
Assuming there aren't any hardware issues, is...
Can I use J-Link EDU for nRF52840-PDK , nRF Connect , please?
Is it sufficient?
What the J-Link PRO provides for nRF52840-PDK, nRF Connect that the J-Link EDU does not?
Question preamble
I am writing a bluetooth application where two nRF5 devices will be in a master / slave configuration. However, I want to be able to flick a physical...
Hi.
I have an application that needs a low security encryption. Therefore I want to use "Just works" encryption. The pairing process is assumed to be in a "safe" place...
I am having a strange problem. After I flash the program to the NRF52 and do a reset (does not matter whether it is a soft reset or pin reset) the system (DK and my own board...
Hi,
i read this post:
devzone.nordicsemi.com/.../
and found the PCA20006 project but i cannot load it to the beacon. I can find proper instructions on how to load...
I had initially added ble_dfu buttonless DFU support (unbonded) to my app per instructions here: infocenter.nordicsemi.com/.../service_dfu.html
Long story short, based...
What unique information can I use to know which physical device disconnected for example? Say I have a MAC address or a name encoded into the advertising packet. Correct me...
Here the connect method is called
err_code =
sd_ble_gap_connect(
peer_addr,
&m_scan_params,
&m_connection_param,
APP_BLE_CONN_CFG_TAG);
In the ble event...
I'm tring to connect my phone to the multi-connect example client app
I'm tracing the ble events in the ble_evt_handler.
When I open the server app on my phone, I see...
Hi Engineers!
faced with a problem of SAADC impedance too small (4,7K)!
We use SINGLE ENDING 8bit mode with following settings:
NRF_SAADC_REFERENCE_VDD4
NRF_SAADC_GAIN1_4...
We are moving from a PCB using a nRF51822 QFAB module to a newer PCB using an nRF51822 QFAC module.
We observed that with the new QFAC PCB we have a significant connection...
I want to use the nrf52dk PCA10040 to remote program a BC832 chip from Fastel.
They say:
"BC832 V1 pin B3 C3 (DCC, DEC4) needs to be connected to the program can be burned...
I have an nrf52832 BLE HIDS device based, with the connection and peer handling code copied from the hids keyboard example, SDK13. I use Windows 10 as host. Setting up a connection...
