after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hello,
I'm using nRF52 SDK12.2 "ble_app_uart_c" project as a "Central", and the target device is the "Peripheral."
Test Steps:
Using putty sending message(with...
How can i initialise all four channel of pwm1 using pwm library.
i need to initialise one channel for one purpose and other channel for different purpose.
whenever i am...
Hi,
I just tried the example from
github.com/.../nrf52-mpu-easydma-using-gpiote-and-registers
And they are working like a charm. Now I want to change the example...
In the on_ble_evt(ble_evt_t*) function from the ble_app_template, I added a case of 'BLE_GATTS_EVT_WRITE'. In it has the following code:
case BLE_GATTS_EVT_WRITE:
{ ...
I have a hard time figuring out what some of the constants in nrf_mesh_config_node_app.h for my Bluetooth Mesh application should be set as.
Instead of writing a question...
Hello,
I'm working with ANT+ hrm profile and the relative Nordic's library, but I find out that there are missing pages. Infact I have only pages from 0 to 4. How can I add...
Hi,
I have taken the BLE Central Example code (ble_app_uart_c)in one nRF51822 hardware and in the other nRF51822 hardware, I have taken the BLE Peripheral Example(ble_app_uart...
Hello dear Nordic Semiconductor!!! I took your wonderful Thingy:52 everything was great until I wanted to build a project based on your Thingy: 52-SDK. I have nrf52840 pdk...
hi, i am having a doubt. now my nrf 52840 is acting as a peripheral. it is advertising some packets and my mobile is acting as a central and receiving the advertising packets...
Hi there,
First: I’m a newby, just did some things with Arduino to control some LEDs etc but not much more before.
What’s my plan: I actually ‘ld lik to control some...
I am new to BLE development and have started by installing SEGGER Embedded Studio
Release 3.30 and have a J-LINK edu usb device and a Core51822 board from Wavetek.
I understand...
I am using various sensors to build a wireless sensor network. There are libraries for sensors that are provided by developers such as from adafruit or sparkfun. I have been...
What is the easiest way to use Arduino libraries into nrf52 projects in Keil on C?
Arduino has a lot minus : bad ide, not support debug mode, not optimize code size. But...
I work with nRF52832, based on SDK 14.0.0, and I have done DFU operation successfully with nRF connect on iOS, but when I used Android phone, nRF connect couldn't start DFU...
