Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
Hello,
I have an application where I want to read the voltage of a battery every 5 minutes for this I'm using the Zephyr ADC library. But now I also want to read the ADC...
Hello Folks,
I've got a thorny problem that I've spent an entire day minimizing before even trying to post about it here.
Before diving in, however, here are my environment...
Hello,
I want to utilize two units of nRF7002-DK I have, to evaluate LE bluetooth link between the nRF5340 SoCs. I need access to define CIG and CIS between the two SoCs...
Hello,
Im using custom board carring nrf52820,and i want enable UART to contact with another mcu,this is the Schematic.
NCS V2.6.0.I take Peripherial_uart to Peripherial_hid_keyboard...
Hi,
I have a Zephyr ZigBee project based on the Nordic Light Bulb example and a custom ZigBee2MQTT integration. However, I can not trigger an identification on ZigBee2MQTT...
I am using the nRF52840, which has BLE support but does not have a touch sensor. Can you recommend a module that includes both a touch sensor and Bluetooth?
I'm now trying to test dongle on nrf52840dongle board：
1. west build -b nrf52840dongle_nrf52840 -- -DCONF_FILE=prj_4llpmconn.conf
2. open nRF Connect for Desktop's Programmer...
hi
board : nrf52840dk
sdk : nrf connect sdk v2.6.1
example: matter light bulb
problem:
I want to add another set of PWM to the sample code. How should I configure...
The docu page for the nRF9151
https://docs.nordicsemi.com/bundle/ps_nrf9151/page/ip/radio_lte/doc/frontpage.html
contains a link to
docs.nordicsemi.com/.../intro_nrf9160...
I have customed my own 52820 dongle board.
I wanted to run ncs2.7.0/zephyr/samples/subsys/usb/cdc_acm demo on my board to test whether it worked. So, I builit the cdc_acm...
Hi
I'm trying to make the UART-HCI example run on my nRF5340-DK board.
Environment: - nRF5340-DK Version 2.0.0 (2022.13) - nRFConnect 2.7.0
I've built the example with...
Hi All.
A few years ago, Nordic documentation for developers included many "examples" to practice with and learn about this technology. For instance, ... >examples>ble peripheral...
Hello,
I am in the process of adding LPN nodes to my network, Unfortunately I am getting a lot of "Ignoring old SeqAuth" Warnings and looking at the LPN friendship call...
Hi
i bound rtc in nrf52833 and set/get the time.
but the time is not incrementing ,iam reading the same time which i set.
i added the config below,
but no change in...
Hello,
I am trying to configure P0.9 as output and toggle this pin.
It is no possible but if I change the number of the pin then I can see the modification of the output...
