Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
I'm trying to figure where the BLE bottlenecks are to figure if I should use BLE or maybe Gazell for my product. I've just started to use the BLE stack, so I guess that there...
hi,
i am working with the nRF51822 development kit and trying to load the sample programs given by the nordic guys, the samples without using BLE is working properly but...
Hello,
While debugging, I found that if there was an active BLE connection, the chip would reset when I switch to single step mode, is there a way to avoid this from happening...
From the log:
[23:41:27.2] EnableServices({11:2,16:2,22:2,28:1,})
I suggest that you use hex for the handles - this is what you use upon inspection and other log statements...
I'm currently trying to learn the functions of the softdevice by using the HTS example. I've managed to make an additional temparature service (named custom), which almost...
Hi,
How to reset the system whenever a particular write event is received from the BLE stack. I made some changes on the ble_app_hrs sample code as follows,
void ble_hrs_on_ble_evt...
I refuse to pay over $3200 for the Keil PK51 Professional Developer's Kit. I would only be using it with the nRF8001 DK. The C51 Evaluation Software is limited to 2K! I am...
I have been successfully communicating with the PCA10001 evaluation kit using the virtual serial port that is exposed by the J-Link interface on the board.
I've now moved...
Hello,
Where do we buy the nRF51922 DK / EK kits? I do not see any purchase links online.
Also, how flexible is the ARM core for programming ?
Thank you!
I'm testing with changing these constant definitions...
MIN_CONN_INTERVAL
MAX_CONN_INTERVAL
SLAVE_LATENCY
CONN_SUP_TIMEOUT
... but I've noticed that I can't set...
Hi,
We are using nRF51822 evaluation kit. Actually we are trying to know how the device firmware upgrade is working.
As mentioned in the nrf51 sdk manual, we did flashing...
Hi,
i need to store data in my Flash, for that i use the flashwrite example. Am i right taht i can use the remain of my application flash? So all flash = 256 kB - App ...
Hello everybody
it's a couple of mounth that our company is working on nrf24L01P .It works fine but there is a problem with cordless phone.
when I make a call with the a...
Hi
Is timer ,gpio ,and spi pheripherals are accessible while bluetooth stack is enabled.
and if it is yes , these are directly accessible or we need to use soft device...
But in button event handler.
i want data to read from eeprom through i2c bus. and send it
through bluetooth stack for every press of buuton 0.
but in master control...
