If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
in nrf/system_off example, to disable uart with suspend
err = pm_device_action_run ( uart , PM_DEVICE_ACTION_SUSPEND );
I want to know how to disable SPI, PWM, ADC...
Hi there,
The blinky sample worked fine on the nRF52840-dongle when programmed via the stock bootloader, but I need to flash it via J-Link to reproduce an issue.
When...
Hello,We have tested the mesh v2.1.1 in the nRF52830 chip, I want to add a PA/LNA with the nRF52832 so that range anxiety can be reduced.we successfully configured and tested...
Hello !
So i have this issue. I use nrf52840 Dongle, from some article long time ago i saw that i cant connect dongle to VS Code because it does not support bootloader,...
Hi,
As well know, nRF52832 TWI interface can support clock stretch function.
Can I disable "clock stretch function" function?
How to do this job?
Thank you
I am working on nrf52840 and using v2.7.0 SDK. in led_state_def.h (i modified it a little)
static const struct led_effect led_effect [] = {
[ LED_EFFECT_ID_OFF ] = LED_EFFECT_LED_OFF...
I am using SDK16 and attempting to load images for loading.I have questions and would welcome pointers
1. I need to use the application to load a new image into memory ready...
Hi,
I'm working through building my own Matter device. Building on MacOS, VSCode on 2.7.0. I'm using an nrf52840DK for now.
I have two endpoints that contain a temperature...
https://community.element14.com/products/roadtest/rv/roadtest_reviews/1646/draft_for_nrf5340
Above link is a user experience with one of you development kits, which is typical...
Hi, we are working on an application that makes heavy use of work queues. We'd like some way to monitor work queue events to optimize timings/priorities etc. I was looking...
I am trying to make a remote control with NRF24 and Atmega328p. The full name of the NRF24 I am using is E01-ML01SP2. I fixed everything but it draws too much current. I have...
We are looking for BLE Mesh Sniffer,
it has come to our notice nordic provides nrf sniffer. can we sniff BLE Mesh Packet?
Will this mentioned link sniffer be of any use...
Hi all,
I have developed a project for nrf52811 on nrf52840DK.
My question is how I flash this project into nrf52811 using nrf52840DK.
I am using nrf5 sdk 17.1.0...
Case 1: Constantly power on reset during the network attachment process. The customer produced 2000 pcs , 300 pcs defective rate. We measured the voltage of VDD1 and VDD2...
I modified the BLE fundamentals lesson 5 exercise 2 example ( github repo ) for my purposes. This uses a generated passkey for pairing with accept lists.
I removed the...
