I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
nRF Connect SDK v3.2.0
Write code:
Read code:
Log:
The address seen on the phone is usually not "06 05 04 03 02 01", but sometimes it is "06 05 04 03 02...
After the PPK II had been stored for a long period of time, it was recently taken out to measure current. It was observed that, regardless of whether Source Meter mode or...
Hi all,
I have been attempting to get the nRF Connect VS Code extension setup to try out some samples on the nRF9161-DK board.
I'm currently having a problem with a version...
Clarify the minimum mandatory external connections and pin/rail requirements for an nRF9151 to boot and run a flashed application, and determine why serial_lte_modem (SLM...
Hi,
I'm working on an application that I recently updated to ncs v3.1.0 (from v2.9.1). For most of the development, I have been working with the nrf54l15 as build target...
HI
I have replaced the external flash used with the nRF54L15 with a different model. How should I set the sfdp-bfp parameters for this new flash?
Thanks!
Using nRF5340-DK, nRF Connect for VS Code 2026.1, ncs v3.1.1 I'm interfacing over a SPI bus to a custom ASIC that uses MISO as a sort of RTS/CTS kind of idea. While CS is...
Hello,
I'm experiencing an issue where RTT logs stop appearing after MCUboot jumps to the application on nRF52832. The application is running correctly (BLE advertising...
I Just got nRF9151 SMA board, try to test NTN feature , after following instruction to update so called "alpha" firmware, somehow the board can not reflash back to any vesion...
I'm using ncs 3.2.1 with a custom board (Holyiot-20046-v1.0). I used the "Create a new board" function in nRF Connect VSCODE to create the board file. I copied the Zephyr...
hello Nordic
i am working with nrf52832 and nrf52840 using ncs v2.9.2 currently
when trying to build with ncs v3.0.2 i get this error:
File not found: /.../my_app/"sysbuild_swap...
Board : nRF54L15DK
NCS : v3.1.1
When I build an application for the nRF54L15 processor, the "otp" memory region in the auto generated "partitions.yml" file has a size...
Hi there, I have uploaded the BLE sounding reflector code on the xiao nrf54l15 module and after the upload i am getting this on my serial monitor *** Using Zephyr OS v4.2...
Hi,
I am using a custom board based on nrf5340. I have an external QSPI flash that is different from the one defined by default dtsi file of nrf5340. My overlay file throws...
I have a custom board based on nRF5340 with nRF7002 WiFi (duplicated from nrf7002dk board definition). The board builds successfully with west build, but Twister cannot find...
