Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hi, I am trying to get the voltage level of the battery using the AT_command AT%XVBAT which I tested using the at_client sample. I tried integrating it with my current code...
From looking at the code when a message is posted to "all-nodes" fixed group address of 0xFFFF it does not route. I was unable to find this behavior specified anywhere in...
Hi forum,
I am working on nrf52832, using sdk 15.0.0. I want to send the data(command) from esp32 to nRF52832 through Rx ,Tx . I have done connections rx,tx,gnd . I can...
Hi,
We are developing our stack with soft device using nRF52840 as the Controller and have the below queries
1. How to configure a static random BDADDR which will remain...
The error is
CMake Error at ../../../cmake/extensions.cmake:416 (add_library):
No SOURCES given to target: drivers__spi
This similar to
https://devzone.nordicsemi...
Hello everyone,
Hello everyone, I am a beginner in programming with OS based systems. I would like to get more into development with the Zephyr based NCS. For now, I want...
Hello!
I try to run FatFS example (SD card example, pca10040) from nRF5 SDK on my nrf52832 (ebyte e73) with microSD card with no success. No matter what I'm still getting...
Hi,
I am trying to get the time and UNIX time after LTE connected. but getting 0 only.
please log
date_time_update() function does not support in SDK 1.4.2 so I...
Hi,
In "nRF52832 Product Specification v1.4, it recommends 32MHz with 40ppm as below:
as the question mentioned above, can I use one with 10ppm?
thanks
best regards...
Hi,
I am getting assertion failed error when putting the device in System off. Could you please help me understand why?
Below in the code where the error happens:
...
I'm working on modifying the ble_app_uart pca10040_s132 to send strings stored in flash memory over BLE to the nRF connect app on an iphone. From what I understand the uart_event_handle...
Hi There,
I m trying to use the xxxx\SDK's\nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8\examples\peripheral\spi with the nRF52480 Dongle and I already had applied the...
Greetings
I have an NRF51422 QFAAEO running S210 Soft Device version 3.0.
I have written a Bootloader application that uses Ant-FS as the upload mechanism. During testing...
Hello everyone,
is it normal behaviour to lose data on UART reception when BLE scanning and advertising both are active?
So far I didn't lose serial data if I just run...
hi all.
I am trying to change number of data packets in one time interval.
I don't know the senario to change it.
For first step I wrote this code to change the quee...
