I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I am trying to use nrfsniffer to debug connection related issues.
We have a ble connection between central and peripheral and we are sending status updates to the peripheral...
I am building an application nrf52840 SDK v17.0.2 soft device is S140 with Segger embedded studio.
Application is to send advertisement data in one single channel (say channel...
Hi
I am trying to Update the Soft Device from 6.1.1 to 7.0.2 (SDK 15 to 17). Using an NRF52840 Dev Kit I am using nRfgo Studio to:
Erase all
Program the new Soft Device...
Hi
I am trying to Update the Soft Device from 6.1.1 to 7.2.0 (SDK 15 to 17). Using an NRF52840 Dev Kit I am using "nRfgo Studio" to:
Erase all
Program the new Soft...
hello,
i am using nrf52840 in our customised board and i am getting this error while debugging the application
4<debug> nrf_sdh_ble: RAM starts at 0x20004230 <error> app...
Hi all,
Debugging via RTT in Segger Embedded Studio stops working after DFU, however if I connect via JLinkExe + JLinkRTTClient I can still interact and debug via RTT.....
Greetings,
I am currently using nRF5 SDK 16.0.0, Softdevice s140_nrf52_7.0.1_softdevice.hex, and Mesh SDK 4.2.0. I migrated all my code base from nRF5 SDK 15.3.0, Softdevice...
Is there a way to obtain context on when a particular BLE transmission ends
RADIO_STATE_STATE_TxDisable == NRF_RADIO->STATE
An by context I mean to know what handle was...
Hello all i want to do a task that is control another LED using ble_app_blinky. In the ble_app_blinky project a characteristic is used to control an onboad LED. I have connected...
Hello
I have a custom board with nRF52840 and have migrated from TWI legacy driver to nrfx_twim. Im trying to communicate with accelerometer and gyroscope chip. With legacy...
Hello forum,
I have a new project that requires Bluetooth connectivity and I think that the nRF52805 suits me best due to its very small size.
The nRF52805 would work...
Hi, I would like to test sample bluetooth code ( ex: central) with nrf5340 dk, what's the difference between central for cpuapp and cpunet ? which one i have to load , cpunet...
I am trying to read Manufacturer Specific Data from a non-connectable advertisement packet from a pressure sensor.
I followed the example in https://devzone.nordicsemi.com...
I have used the nrf9160 development board and it can works rightly. But from this week, it doesn't work. I can download my code to the board, but it doesn't work. When I press...
