I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hi,
I am using nrf52 development kit . I connected peripheral device and communicate all characteristics using DK.
But i want read rssi value from peripheral. I didnt...
Hi,
Do do you know of any Xamarin Development being done using your development kits?
Trying to determine the best way to get up and going using Xamarin vs native iOS...
Hi there,
Just wondering why serial_uartes example has been removed from SDK17, We have to use 2 uarts at the same time.
Is it intentional or accidental ?
Thanks,...
Hi everyone. I'm using a Thingy:91 and the asset tracker application. I can compile and flash (using SES and a Segger J-Link) the application and the device connects to the...
Hello,
I read your white paper nWP-030 about selecting the decouping caps. But I didn't find any explanation why you also specify maximum values for the caps. Especially...
Hey,
I am using SDK12, S130, nRF51822;
Trying to create a DFU update for application which Also writes over a certain area in the reserve app data, in the end of the designated...
Hi,
I'm using 52833 and S113.
My system works well, i have all my caracteristic and i'm able to read it out with nRfConnect mobile app.
But it is terribly slow .
I...
I'm using nRF52832 S132 and migrating from SDK 15.2 to SDK 17.0
My previous code used nrf_serial which appears is no longer available in SDK 17. I don't see any info in...
Hello everyone,
I would like to add ble secure bootloader on my NRF52840 dongle, I have already do that with the nrf 52832 DK But there is no example in the SDK for PCA10059...
I need to write received data from SPI to address pointed by a parameter. When doing a transfer, spi drivers also read the data sent by slave during TX. I know this is normal...
Hi all:
I am use ble_app_blinky demo sdk 16.0.0 I want to put system on idle mode,but there need to call two times sd_app_env_wait() so it can in system on idle mode.
...
Hey,
I am a new to BLE devices. I am using BL651 Laird Connectivity's 453-00005 module
and using standalone JLink OB ARM debugger to connect.
When I try to connect my...
Hi,
I want to get running the sample "lwm2m_client" on the board nRF9160DK (PCA10090).
Modem FW Version: 1.2.0.
I build the sample with Segger Embedded Studio v4.52...
