Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello. I want to use nRF52810 as a connectvity platform connected to OpenWRT MIPS based board via UART. For some reason the only solution I can assure is to use 2 wire UART...
Dear Nordic support,
We are using SDK5 15.2.
Our application uses FDS to maintain configuration. One issue is that we have to change the configuration via phone app regularly...
Hi,
I am working on nRF52840 DK . C:\Nordic\SDK\nRF5SDK17009d13099\nRF5_SDK_17.0.0_9d13099\examples\peripheral\ uart I am sending data from Arduino and showing it on PuTTY...
Hi All:
I try to create a custom Characteristic,with nrf_ble_qwr,
but when set is_defered_write = 1;
connect with NRF_CONNECT APP, I can't write under than 20 byte,if...
Hi, we just saw that %BSKGEN was added in MFW 1.2.1. However, it is not clear to us what is the intended use of it. Could you please give us a bigger picture of it?
Is...
Hi there,
I have a rudimentary understanding of programming with the nRF chipsets and Segger.
In our project, we are trying to locate the position of a transmitter (nRF52833...
when design the product, BLE output power set at +4dBm, and test the real output power with Spectrum Analyzer. when test at the MCU direct output pin the output power is about...
Hello -
We are developing on the nRF52840-DK, using SDK 15.3.0 and FreeRTOS with tickless idle. The SoftDevice is disabled. Using the PPK v2.3.1 when our app is in System...
Hi,
I have nRF9160-DK kit and its environment is set such as nRF Connect SDK and Segger Embedded Studio.
I want to build a simple application from scratch for example...
Hi,
I have a question regarding our approach to achieving high throughput UART transmission over BLE.
The protoboards we are currently testing have BL654 modules from...
Hi !
I tried to connect Thingy:91 to the nrfcloud using iBasis SIM in Germany. I want to try different telecom provider like Vodafone or Deutsche Telekom. Any recommendations...
So as part of my system I have something much like the Nordic UART service in that I need to send a notification when something arrives from the UART. Mine is a little bit...
For a Bluetooth Mesh device, or ' provisioned node ' , does provisioning happen more than once for a established network? Will this device ever need to be re-provisioned once...
Hi,
Is there is a sample for using the nrf-9610 I/O input for A2D to read a voltage across a resistor(using P and N for differential), given that I'm having Zephyr as ROS...
