I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hello.
C21, L5 and C22 are part of antenna matching. And, L6,L7,C23, C17,C19,L4,C20 they suppress the harmonics and spurious responses and match the chip to 50 ohm. R19...
Hello,
I am trying to setup the DTM to evaluate our product. I am using shielded boxes and following the setup from application note 34:
I am unfamiliar with this...
Hi all,
I added ble central multilink example with ble_app_uart_c code, i am able to compile code successfully, but not able to run this code on board due to this error...
Hi!
I am developing a project where an NRF52840 DK is receiving data from the environment using BLE. I can observe the received data using NRF_LOG_xxx() command in my...
I'm trying to use the PA/LNA control feature in S112. However I only want this to be enabled when under specific conditions/configurations at runtime. So I need a way for...
There are 6 channels per the SDK (nRF5_SDK_15.3.0_59ac345) and the product spec for nRF52840 but I cannot seem to get channels 4&5 to do a compare or capture. Using Keil's...
Anybody got any hints at how to get Zephyr to work on the nrf52840 PCA10059 dongle?
After many struggles, I was finally able to compile Zephyr's sample/bluetooth/hci_usb...
Hi there,
I am trying to get I2C communication up and running with the nRF52832 (specifically configuring the nRF52832 as a master to communicate with 3 slave devices),...
Hello everyone,
I am developing a temperature and gas sensor for indoor environment monitoring. Due to the limitation of the bluetooth transmission range, I hope to add...
Hello, I am developping on a nrf52840-DK board and try to debug using a Black Magic probe. Software is based on softdevice, GCC build chain and Visual Studio Code with Cortex...
I've been wrestling with this DK for some time now, but today I tried to get the LTE Link Monitor app to run and see what outputs I could get. I ran everything the same as...
Hi,
I am having issues, getting the uart backend logging working on a nrf52840 dongle. I'm testing the logging on the standard blinky example that came with the sdk (15...
Hi,
Upgrading from nrfConnect for Desktop from v 2.6 to v 2.7 and higher and its associated apps seems to hang on Linux (ubuntu 16.04). 'strace' suggests that the problem...
I have a design which mainly needs to be a peripheral, however I was told that I need to use the multi-pheripheral example as I may need the device to switch to a central...
