If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I use the following code to write 32-byte to L01-module. (The wireless-communication works successfully ).
The following ( 420us+200us ), accompany only 32-byte wireless...
Hi.Is there any inbuilt ic present in nrf52840 DK board to monitor battery management ??if so, how to use that for measuring battery life?can anyone help me out plz!!
Thanks...
Good afternoon, I have a new small, but I think important, question. I did not find a concrete answer on this forum. The question concerns the correct switching of buffers...
I had try to use nRF connect to connect between nRF52840 Dongle and the bluetooth of application.
(I'm not sure the model of bluetooth of application.)
It's connected...
How many crystals/oscillators do I needfor a NRF51822 WLSCP chip?
I looked at datasheet and I'm assuming I will need a 16 Mhz crystal, a 32Mhz crystal, a 16 Mhz oscillator...
I am using IAR workbench and working with the nrf52 DK, using the S132 v.3.0 softdevice. I used the blinky example code to connect the nrf52 with my android phone over BLE...
Hello,
I got TCP Server example working on nRF52DK with Raspberry Pi.
I set everything up and can ping global addresses of DK on all interfaces (wlan0, eth0 and bt0) from...
Hello,
I am using NRF52832, SDK v15.1.0.
For advertising on single channel, I added " p_advertising->adv_params.channel_mask[4] = 03; " in ble_advertising_start() ,...
SEGGER Embedded Studio 3.12
nRF52 SDK 15.0.0
In order to generate peripheral driver library files，how to create library in project(have .c&.h file in this project).Only...
Hi,
SDK documentation says "You cannot write to UICR.BOOTLOADERADDR when using the default J-Link target driver in IAR". Some threads suggested it is only nRF51 issue, but...
Hi!!
Now I am using sdk 14.0.0 / example / peripheral / spi / pca 10040 / blank / arm5_no_packs /
I am sending commands to ads 1192 with nRF 52832 DK as master and after...
I had an issue on using HID to control the media in Android. It worked fine at the first connection, I could play , pause and change the song on phone. But it couldn't control...
Hi I would like to confirm which NRF51822 models are the 0.35mm thin WLSCP package. I checked Avnet distributor and they say that NRF51822-CTAC-R7 is 0.35mm but the package...
Hello everyone, the sdk version that I use is 15.0 (nrF5_SDK_15.0.0). The soft device is s132.
I need to make an android custom app (with UART functionality) so that only...
I'm trying to get a third party demo application working and I seem to be having an issue with the nrfx_spi_xfer function getting stuck waiting for the NRF_SPI_EVENT_READY...
