Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi, I am developing using nrf52832 and st7735s.
Successfully displayed the lcd screen using the code in \examples\peripheral\gfx
However, when screen clear, text_8print...
Dear friend I checked the data sheet of 52820 and I didn't see any LPCOMP peripherals. Check the data sheet of 52832, there are LPCOMP peripherals. Comparing COMP and LPCOMP...
I am using NCS V3.0.2 with a custom nRF52840 board, which functions as a BLE peripheral. The application that I am working on fully depends on the BLE connection, so the crucial...
Hello. We need to add more end devices than default (10) on our Zigbee coordinator and that was solved with
zb_set_max_children( ZB_DEFAULT_MAX_CHILDREN );
where ZB_DEFAULT_MAX_CHILDREN...
Hi, I use nrfconnect SDK 3.1.1 and nRF52840 (as a dongle, DK etc) Using the power profiler kit 2 I see legacy advertising (TX/RX) peaks of about 32mA (with txpwr=8dBm, 3.2V...
Hi guys,
I'm working on this project which was basically a migration from STM32 to the nordic NRF52832 in order to enable the BLE beaconing mode.
It has been a challenge...
Dear Nordic Support,
I’m working with a Thingy:53 device and encountered a persistent issue during recovery. The device is recognized via J-Link (serial number: 1057760136...
Hi everyone, I'm trying to set up a bootloader chain using sysbuild (NSIB → MCUboot → APP) so that MCUboot can act as an upgradable bootloader. I'm working with the nRF54L15...
What is the permitted VDD ripple on the nRF9151?
I see " To minimize supply voltage ripple and suppress EMI coupling to and from nRF9151 VDD , keep supply network impedance...
Hardware Setup
Custom Board:
nRF52811 chip
No external LFXO (32.768 kHz crystal)
No LC filter for DC-DC regulator
No peripherals connected (no LEDs, buttons, sensors...
Hi,
I try to use the west ncs-sbom command to generate the result, however i meet below error happening but I had not idea how to solve it could someone help me to check...
The issue is that , i have custom board which have nrf52833 and nrf21540 (Range extender) , i have to increase the range of tx gain = 20dbm using gpio method
this is my...
Hello,
I have developed a bootloader with OTA update functionality on an nRF device. The partition switching code (bootloader jumping to the application after OTA) works...
I am running into a recurring issue with attempting to connect to a nRF52840DK advertising using extended advertising from iOS devices. Connections repeatedly fail to establish...
I am not using the nrf5340DK development board; instead, I am using the nrf5340 chip, and the SDK version I'm using is V3.1.0. I defined the I2C child node "lt3582" in the...
I set CONFIG_BT_DEVICE_NAME_DYNAMIC=y in prj.conf, and then called it after the system started.
These functions modify the Bluetooth name, but the new Bluetooth name has...
