I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
I am trying to run the ble_app_uart from the ble_peripheral folder in the NRF SDK 15_2 I am testing with a Nordic 52840 DK (PC10040). I have made essentially no changes. ...
Hi, Nordic staff.
I'm working with Central device using S132.
There is a peripheral device using S112 in Nordic. I didn't make this peripheral.
My question is...
Hello all.
I have a question relate to: How to "ble_app_hids_keyboard" app can connect multi device?
My task: make equip peripheral base on nrf52811/840 can Adv and connect...
Hello, I am new to Nordic, I was previously using Cypress CYBT343026-01. But there were some drawbacks found during development. 1. It was consuming 315μA at 0 dBm BLE tx...
Perusing the GCC linker script supplied as part of SDK v16, I noticed that the .data section is specified as follows:
.data : AT (__etext) { __data_start__ = .; *(vtable...
I now need to burn the app firmware and modem firmware of multiple 9160 chips at the same time. Using pynrfjprog to write a program to burn the firmware for ten chips(Open...
Hello
I'm going to use a potentiometer to control the pwm. I am using a 10K potentiometer and have used a saadc example.
I printed out the value of adc through this example...
Hi everyone,
I've just been working with NRF52833 and nRF5 SDK for Thread and Zigbee v4.1.0 to create a zigbee mesh network for home automation. My network is pretty simple...
Dear Members,
I saw this code ,
If there is no input, how can I handle it and display result = 0 and not shutting down CPU ?
How can I display 0 from this code...
Hi.
I want to disable the TWI master's internal pull-ups on SCL and SDA. So I set it according to the contents of the following URL, but the setting is not reflected as...
Dear Nordic Support team,
Currently I am in the process of adding the USBD_CDC_ACM driver code to our existing application following your usbd_ble_uart example. I can receive...
Hi，
Our customer is using nrf9160.There is a problem about powem_on circuit .
Attach is the schematic diagram:
Here VBAT is 4V,PW_ON is connecting to the nrf9160...
Hi,
I'm using nRF52810.
And i'm trying to measure battery level using saadc.
The problem is saadc result is not accuracy.
When battery voltage is 3.3v, saadc value...
