I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I am currently developing a stationary BLE device. I am testing the nRF52840-dongle in combination with the pc-ble-driver. For that purpose, I am using the connectivity_4...
SDK: 15.3.0 Device: EYSHJNZWZ (nRF52832)
I am operating in a "peripheral" configuration, with bonding enabled. "BLE_GATTS_EVT_WRITE" occurs when notification is permitted...
We're porting over some software to the Arduino Nano 33 BLE Sense. This board comes with an nRF52840 clocked at a max. of 64MHz. However, the same code runs about 2x slower...
I want to send Tx power in advertisement packet.
Currently I am using following code.
int8_t txpower_level;
static ble_advertising_init_t init =
{
....
Customers use nrf52810 flash program to store data, but want to know what flash start and end address can be written, please point out that you can refer to that document...
Dear Nordic Semiconductor
I am using device:
NRF51802 bluetooth 4.0
Product Introduction:
Features:
1.Adopt NRF51802 bluetooth 4.0 BLE SOC
2.ARM CORTEX-M0
3...
Hi , I use the pc-ble-driver to developer desktop tools, like nRF Connect. Unfortunately, I don't know Java. I‘ve tried to used examples that work(heart_rate_collector and...
Hello,
We use a custom interface board to program and run test programs on our series of tiny BLE modules based on nRF52xxx series (ISP1507, ISP1807, ISP1907).
Our interface...
Hello ,
The test of CPS/SEN/SPE/BI-04-C [Procedure Already In Progress] failed.
While this test, the tester sometimes received the unexpected ATT Disconnect which our...
I want to advertise a data in ble_app_uart continuously after equal interval of time. Can you please give me some clue. I don't want to use beacon here
Hi,
I am currently trying to implement a beacon scanner and want to filter out all advertisements except beacons. Is there something in the beacon advertising packet that...
Hello everyone,
I am working with nrf5_SDK_16.0.0 and using VS Code as IDE. When I open the "stdint.h" header file in VS Code, the 16-bit compiler is enabled:
But, I...
Dear sir,
If I dump the hex file of this path "nRF5_SDK_16.0.0_98a08e2\examples\ble_peripheral\ble_app_uart\hex" then the code is working fine. But if I dump the hex file...