I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hi,
I tried to add 3 characteristics and 1 gatt service to my NRF52810 using with development board with 10040e (I am using gcc compiler). Then I got a error which is saying...
we are considering using .005" thick stainless steel to provide better bridging effect across the opening on the board for the battery. This will provide more strength to...
Hi
I am trying to use an antenna switching board for AoA direction finding. I know that the RADIO controls 8 PSEL.DFEGPIO pins to control switching antenna.
1. Could...
Hi,
We want to use the NRF52810 without radio and we don't want to put the external oscillator to reduce the PCB size
I would like to know if necessary to have the external...
Hi,
Some time i could not put break points inside main for sample projects provided for nRF91, i tried clean build, erasing the flash 'nrfjprog -e' and evn enable the configuration...
We would like to use a Dongle based on the nRF52840 as a BLE Central communication via NUS to our product. The example in the nRF Connect Desktop does just wat we need on...
Hi，
I want to use none secure example on nrf5340.
The code can't run with ns config(uart didn't log anything),But it works fine with normal config.
How can I sovle this...
Hi, devzone.
Since I was recommended last time, I started reading the BLE tutorial .
I first saw a this tutorial .
Even if nrF52-ble-tutorial-advertising is placed in...
Hi,
I have a custom nRF52840 board. I mistakenly tried flashing the custom nRF52840 board with STM32 firmware. From that moment on, I can't flash board. When connected...
Hi,
I want to create 2 softdevice tasks, 1 for advertising and 1 for scanning. I have ported the dependencies and some code from the ble_app_freertos_pca10040_s132 into...
I have two Nordic nRF52840 DK Boards and I need to check the performance of BLR-LR i.e. how much range do I get in Indoor Environment and in Open Environment.
Can someone...
Hi
We want to add one flash partition to use to store external host files by http downloading, so we changed the dts to below:
then we duplicated the dfu_target_mcuboot...
Actually i was working previously on nRF51422 DK, to test its range by configuring my DK as an advertiser, and observing RSSI values of the beacon on nRF Connect app.
the...
Is it possible to have both BLE and NFC passive device at the same time.
I tried combining 2 examples but I am running into a conflict of SOFTDEVICE_PRESENT definition....
When using emStudio and configuring a project via the GUI menu (Project -> Configure nRF Connect SDK Project), the resulting config is generated in <build_folder>/zephyr/...
