I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hi all,
I am currently developing on the RIGADO BMD-300 (nRF52832) eval board. I have the following code setup to interrupt on a button press (aim is to have 9 buttons)...
I am working on an application targeting the Fanstel BT840X, which combines nRF52840 and Skyworks SKY66112-11 PA / LNA on a single module.
I am using GPIOTE and PPI to drive...
Hi Nordic devzone...
I want to form a ble mesh network through which a Central can reach any Peripheral in the network, if not directly then through other peripheral. The...
Hi,
I'm following the Border Router Quick Start Guide . In it, it states:
To change the settings, edit the /etc/config/thread_border_router file.
However, that file...
Dear experts, please tell me, how can I switch the frequency source for the RTS from STAL to internal RC generator when the processor is running? command sequence does not...
Hello,
im using nrf52832 NRF5 SDK 12.2 , S130 . using the pasted code and i get 1023 on the ADC even voltage is 1.7 volt i using keil ver 5 s130 i double checked the voltage...
Hello,
I have prepared an nRF52840 with DFU example (dfu_nrf52840_xxAA_s140_6_0_0).
When making the DFU package for the blinky example (bin/blinky/blinky_nrf52840_xxAA_s140_6...
Hi all,
I'm working with 2.1.0 version of Thingy:52 firmware (the last version currently). Further I am working on Linux with SEGGER J-Link Commander V6.34c in order to...
Hi,
I want to read register 0x00 (chip ID) of ads1292. i do following...
===========================================================================================...
Hi
I am developing 4 layer PCB for the nRF51822 with a power and a ground plane in the inner layers. I will be using a balun from Johanson Technology (2450BM14E0003) with...
Looking to apply an nRF52 chip in a wearable device... ideally without mounting it on a board.
Is that remotely feasible?
It would still be necessary to connect to 12...
Hi to all,
i have a project that was based on SDK 13 and in that version i had a bility to call fds_record_write with multiple data chunk, but in softdevice 14 and sdk15...
I have integrated the code of the multilink into the uart central example. The project can be built without error. however, it is not possible to establish a connection to...
Hi,
I'm starting development of a new product utilizing nRF52840 mcu. We used this chip in previous product with Bluetooh stack (SoftDevice). I didn't participate on this...
