Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
In datasheet it had been mentioned that in SPIM0,SPIM1,SPIM2 the SPI clock frequency should not exceed more that 8 Mhz. And SPIM3 nothing is mentioned. Can we understand that...
Hi, I tried to use pc-ble-driver-py script to talk to a nRF52840 DK. It works perfectly with the official connectivity app hex file (the one nRF-Connect PC application loads...
I modified the nRF5 SDK 15.1 example program serial to display a message on a physical device. I added a blinky service to the ble_app_template example program and I am able...
Hi, thank you for looking at my post.
I am using Keil V5.25.2.0 with a nRF51422. I am using the soft device "s310_nrf51422_1.0.0-2.alpha_softdevice." My memory regions for...
So, currently I utilize DK's to program and debug both pca10040 and pca10056 utilizing a custom shield that plugs into any of the nRF52 DKs. The programming and the debugging...
I used SDK15 and ble_app_uart_c.
I start a UART timer sending and start a LED timer. There is a probability of app: SOFTDEVICE: ASSERTION FAILED in the process of running...
Hello all,
I'm using the Nordic SDK 14.2 BSP button handler. I have a push, release, and long push event on a single button. These are working as expected -
Except when...
Hi all
I am using the spi0 to storage the data and twi0 to get sensor data . But after I add the file nrf_drv_twi.c and compile , it complies wrong :.
\_build\nrf51422_xxac...
I have problems with disconnecting my Android devices from my BLE peripheral. I don't think this is Nordic-specific, but perhaps someone has an idea?
Disconnecting using...
Hello,
i have a application with two operating states state1: device is in deep sleep state 2: device is running
i wake up the device from deep sleep via gpio interrupt...
Hi
I am integrating your Android DFU library with our mobile app to do FOTA to our Nordic device nRF52832 . We are using SDK 14.2 and doing the firmware update using zip...
I have the nRF51-DK and have installed Python etc. and the nrf_sniffer_2.0.0-beta-1_51296aa.
3 .hex files are in that installer: sniffer_pca10028_51296aa.hex, sniffer_pca10031_51296aa...
Hello,
I'm trying to shutdown my whole system (nRF 52832, SD132, SDK 12.3) after advertisement fast and slow are finished, following the structure of the peripheral BLE_APP_UART...
Hi,
I am trying to run lightswitch example in MDK.
Provisioner keep logging : 419, Unhandled Mesh Event: 4
Button 1 is in on state.
and LD5 is keep blinking.
these...
