I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hi guys,
I have nRF51822 Evaluation Kit.
I am trying to make simple project for my senior design.
Here is the setup.
I need to control simple on/off switch from...
Hi, I'm developing a BLE application.
I want to send multiple packets (from same characteristic) per connection interval.
I've read this question:
devzone.nordicsemi...
hello,
I am trying to develop an application using s130 softdevice on NRF51822 board.
i am able to do a undirected adverisement after a scanning. But when i am trying...
Hi
I use proprietary service to transmit data between iOS and nRF51822. The example I referred to is below.
C:\Keil\ARM\Device\Nordic\nrf51822_v6.0.0.43681_Backup\Board...
Hello,
I need to send packets on a specified advertising channel and receive them at the same advertising channel. Unfortunately, the SoftDevice API does not seem to support...
Hi,
I have several nRF51822 which are far away from each other and I want to communicate with all of them without need to go to deferent places to get the signal.
Does...
Hi
What is the scan interval ,while using the nrf51822 dongle as nrf sniffer.Is it possible to change this interval or is there any option provided in the sniffer api ...
Hi, we are using the nRF51422 and the s310 soft device using the 5.2 SDK.
In ble_error_log.c I noticed that you have a comment suggesting that write to flash was removed...
I have already installed nRF51_SDK_7.1.0_372d17a_packs. The examples in this SDK are only for nRF51422. Can I use these example in nRF51822 by just change device to nRF51822...
I was going through the figure 10 of page 35 of nRF24L01+ product specifications and found that when an ACK is received, it checks for only ACK payload. Does it mean that...
Hello,
I have implemented the ble UART service in the s120 example : ble_app_multilink_central. I can receive messages that are sent from a ble UART peripheral in the ...
I'm trying to use the bond manager to store links.
I used the ble_uart application posted in this site by a Nordic employee and tried to use the bond manager as it was done...
Hello,
i can't find the characteristic read timeout in BLE Core SPEC 4.0. If the central device read a characteristic from the peripheral device, in which time the peripheral...
Hello
I have uploaded a hex file which for some reason I cannot see the tag anymore, is there any way to re-program, erase or reflash the beacon kit using nrf51 programmer...
