I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
I'm following the steps in exercise 1 of the nRF Connect SDK Fundamentals and getting configuration failures. From what I can tell it looks like Zephyr is failing to build...
nRF Connect SDK v3.2.0
Write code:
Read code:
Log:
The address seen on the phone is usually not "06 05 04 03 02 01", but sometimes it is "06 05 04 03 02...
After the PPK II had been stored for a long period of time, it was recently taken out to measure current. It was observed that, regardless of whether Source Meter mode or...
Hi all,
I have been attempting to get the nRF Connect VS Code extension setup to try out some samples on the nRF9161-DK board.
I'm currently having a problem with a version...
Clarify the minimum mandatory external connections and pin/rail requirements for an nRF9151 to boot and run a flashed application, and determine why serial_lte_modem (SLM...
Hi,
I'm working on an application that I recently updated to ncs v3.1.0 (from v2.9.1). For most of the development, I have been working with the nrf54l15 as build target...
HI
I have replaced the external flash used with the nRF54L15 with a different model. How should I set the sfdp-bfp parameters for this new flash?
Thanks!
Using nRF5340-DK, nRF Connect for VS Code 2026.1, ncs v3.1.1 I'm interfacing over a SPI bus to a custom ASIC that uses MISO as a sort of RTS/CTS kind of idea. While CS is...
Hello,
I'm experiencing an issue where RTT logs stop appearing after MCUboot jumps to the application on nRF52832. The application is running correctly (BLE advertising...
I Just got nRF9151 SMA board, try to test NTN feature , after following instruction to update so called "alpha" firmware, somehow the board can not reflash back to any vesion...
I'm using ncs 3.2.1 with a custom board (Holyiot-20046-v1.0). I used the "Create a new board" function in nRF Connect VSCODE to create the board file. I copied the Zephyr...
hello Nordic
i am working with nrf52832 and nrf52840 using ncs v2.9.2 currently
when trying to build with ncs v3.0.2 i get this error:
File not found: /.../my_app/"sysbuild_swap...
Board : nRF54L15DK
NCS : v3.1.1
When I build an application for the nRF54L15 processor, the "otp" memory region in the auto generated "partitions.yml" file has a size...
Hi there, I have uploaded the BLE sounding reflector code on the xiao nrf54l15 module and after the upload i am getting this on my serial monitor *** Using Zephyr OS v4.2...
