My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
I am using a setup with a PCA10040 with the PPK as piggy back. I also use a JLink Ultra+ connected to the "Debug in" connector on the PCA10040. I have cut the SB20,21,26,27...
Hi, I am working on custom board with nrf9160. I want to use LTE LINK MONITOR but my uart don't work. I create simple helloworld application from samples. I change uart0 rx...
I had tried to advertise in TLM format (in temp variable) of eddystone value coming from sensor ssts751 integrated with my devkit but not getting correct. Please suggest me...
I use nRF5340 DK as Central, iPhone as Peripheral.
I start a scan with no filters and in scan_filter_no_match() I check if RSSI is good enough " RSSI > -40 " and initialize...
Hi all,
I am currently developing on the development board nRF52832, SDK16.0 and SD132v7.2.0.
My development board acts as a slave, while an app that tries to connect...
Hello,
I'm struggling to understand the available RAM size in that chip.
After reading the product specification v1.7, the RAM specification is described as follow:...
Hi,
1. When nRF5340 has no power supply, adding 3.3V power supply to the digital IO port will produce voltage drop.
2. Why does the voltage drop occur?
3. What is the...
I'm trying to port a project from nRF52832 SDK15 to nRF52833 SDK17.
As a first step, I'm trying to get the HRS sample to work, as my other project was based on it. So far...
Hi,
I am trying to decide whether to go with the NRF5 SDK or NRF Connect SDK for use with the NRF52840.
From the compatibility matrix documentation at Infocenter, I can...
Hi,
I'm looking for a solution to update my program with BLE. I need to do it with a mobile app developped in Flutter. I found the Flutter library to flash the Arduino ...
I have a master device and a slave device. The slave device has 6 characteristics, 4 of which are notif. I need to use the master device to obtain the data of these 4 characteristics...
Hello,
I have just bought a nRF5340-DK. My board is labeled 2.0.0, and appears to use a 2nd nRF5340 as the debugger. I am trying to use TF-M with a Rust application. So...
I'm using Linux 20.04. I have been following the manual installation guide for setting up the nRF Connect SDK and also nRF Toolchain
in my .bashrc file:
export PATH=$...
Hello , I am working on a project, Which which currently working fine , but my job is to add some feature to it. So it is a Mesh application i need some kind of custom sleep...
