Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
Setup :
Device: nRF52840DK PCA10056
Software: NCS v1.3.99
What I am trying to do:
I have 3 SAADC sequences that I need to run for my application that I wish to poll...
HI,
I'm using the zigbee CLI example as coordinator and have another CLI device for reference as router. With my sniffer I can log the association sequence with the cli...
Hello,
I have a nrf5340 PDK .
The kit does not work right, because i got a several errors.
For example in nrf connect v.3.6.1 the PDK is shown as 000000123456 also in...
Hello Nordic support,
I would like to confirm whether nrf52840 supports only Bluetooth 5.0 features or does it also support Bluetooth 5.2 features. If it supports Bluetooth...
Hello, I am working on Nrf52 mesh network and need to update device via any host mcu or flash connected with the nrf52. But could not find any way to implement it.
If anyone...
I have changed our code that has been running on v1.4 successfully to v1.5
Mainly because I'm hoping for an improvement in the reliability of the new modem library.
However...
Hi All
Can anyone please point me to any documentation/app note that explains how the UE receives a Valid paging message when Network wants to reach the UE. Is there a...
Hallo,
IDE: Segger Embedded Studio
nrf52840 DK
Custom Board with ProteusIII
I have designed a custom board with ProteusIII (nrf52840 SoC) and was working with...
Hi,
I am currently in India city Bengaluru.
as ibasis sim does not support my region so
i am trying to connect nrf9160 to lte network using airtel sim card, but it is...
Hi,
We are working on a new product with " nRF52832 " IC. We want to test our design RF antenna (PCB trace Antenna) performance. For RF test we found an example code and...
If I change the NRF_SDH_BLE_GATT_MAX_MTU_SIZE in sdk_config.h to any value greater than 23, immediately after connecting the stack executes a sd_ble_gattc_exchange_mtu_request...
Hi, I found that hci_usb sample may not work correctly with nrf5340pdk from the following q&a. It means that nrf5340dk support hci_usb sample?
https://devzone.nordicsemi...
Hi:
I'm using "nRF5_SDK_17.0.2_d674dde"
A question about the macro NRF_LOG_INFO.
the statement in the source code NRF_LOG_INFO("Disconnected connection handle");
...
Hi, all
I just asked similar one yesterday, but I think this should be resolved first.
I want to merge ble_app_uart_c and ble_app_uart.
So I added scan_init / scan_start...
Hi Nordic,
I am trying to make the read and write to the MX25R6435 with QSPI interface, any examples to this? I am using the sdk 17.0.2
Thank you in advance
