If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
Hi, we are considering using Gazell on the nRF52840 with nRF5 SDK v16. What would be the maximum packet length and the maximum data throughput that we could expect? What would...
Howdy,
I am using NRF5 SDK v15.0.0 on an nRF52810 custom PCB and am having a problem where the specified event handler is not being called upon completion of an SPIM transfer...
After unpacking I followed the first step at nordicsemi.com/thingy91, which is to update the firmware. I followed the linked instructions to update the modem and application...
Hi,
I have few questiones to initiate developing our project taking BLE Examples and BLE Services as reference.
Now,First thing we have to do in examples is turn bluetooth...
nRF Connect v3.2.0 - LTE Link Monitor is running on Ubuntu 16.04, and nrf9160 fw is v1.0.1. When connecting the board to my laptop, all Modem, UICC, LTE, PDN are Green. But...
hello
i am working with nrf52832
my code is based on the Ble blinky example from centeral. i added to the code with ble, uart, saadc and pwm and it was working great ...
Hi,
Using nRFConnect for desktop I've noticed that when writing an attribute I usually enter the hex values of a byte array (e.g. "12" = 0x12) but on other occasions the...
Hi Nordic Team,
- Can I UART/SPI/I2C on any pin of NRF52832 which is mentioned general-purpose I/O pin ?
- Can NRF52832 wakeup via any general-purpose pin?
- Is there...
Hello My ap plic ation is based on your bootloader (secure_bootloader_uart_mbr_pca10056) and your example "ble_thread_dyn_mtd_coap_cli".
When I send a special command...
Hello everyone!
I just got a Thingy: 91 and followed the startup guide, updated the firmware, and installed the modem...
I had trouble using iBasis eSIM because there...
My question is how to handle large amounts of data over the Gatt service
Our Current setup is 10 devices all on a Mesh Network. We use nRF5 SDK for Mesh and NRF mesh BLE...
Hello,
My project requires me to send acceleration data to phone. So, i have started with Custom BLE app.
Since i need to send 3 values, of x, y and z-axis. So i need...
hello
i am using nrf52832, with ble (s132 softdevice), pwm drv, saadc drcm uart, and using app_timers
i have added the twi drv to work with an expander for start.
...
We are using the Android-BLE-library version 2.1.1 above Android 9 (API level 28, using Java 8) in order to connect to a BLE-MCU. This MCU advertises a custom BLE profile...