I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
In Beacon Why UUID is required ? Where exactly it will be useful ? I understand Major value Minor values , company identifiers values . it will difference the beacon location...
Hi guys,
i'm trying to deploy a BLE iBeacon on an Holyiot-17120 board. My code runs fine on the nRF52840 USB Dongle DK, but on this board works only when I've debugger...
Hi All,
I want to configure 64 MHz internal oscillator (HFINT) on my nRF9160 DK to reduce the wakeup time of nRF9160 chip from system-off mode. Is there any example available...
Hello,
I'm looking to be able to adjust PWM output frequency around 100KHz in 100Hz (or close to it) steps. I understand that no matter which method you use the implement...
Dear all,
I'd like to customize bootloader, I need more space so i modified flash address from example: FLASH ADDR (0x78000), SIZE (0x6000) to FLASH ADDR (0x69000), SIZE...
I am using the code above and already try it in the compiler . It should work but when I try to display in termite it only display .000 for microseconds.
Example
1987...
I used thingy s132 pca20020 sdk and i changed the code.
send data.accel.x, data.accel.y, data.accel.z data when data over the limit in swith case DRV_MOTION_EVT_RAW in drv_motion_evt_handler...
Hello all!
I've been researching DFU over BLE, between a central and a peripheral.
The peripheral is possible to upgrade over the DFU Bootloader. I've tried upgrading...
Hi,
I try to use cmake in Linux to get the hex file fo bootloader. The Platform is nrf52832_xxAA, the toolchain is gccarmemb. I read the given cmakelists but many variables...
Hello!
I am in the final phase of development and currently focused on reducing power consumption of my device.
To improve power consumption I'd disable UART if not...
Hi,
I am using nrf52 DK board.
After uploading my bootloader and application on a device that is connected through bluetooth with my board, i want to know the application...
Hi,
i'm facing a problem with a connection.what i understand from ble there are 2 mode in ble such as advertising mode and connection mode. i'm working on a project, which...
I have designed a custom board using NRF9160, but it has some trouble such as can't connect to LTE/NB-Iot, detect GPS signal,... So I want to use development kit to set up...
Hello,
SDK: 15.3.0
nRF52840-DK
IDE: SES
Example: flash_fds_s140_pca10056
Example Location: nRF-SDK\examples\peripheral\flash_fds\pca10056\s140\ses
Example Documentation...
It builds OK and I can flash the hex file using nRF connect Programmer. But I need to debug the code but I have not found a way to upload the code and break at main() entry...
