after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Dear all,
I'm using an nRF51822 chip for implementing a BLE HID device (mouse) (SDK ver. 12.3.0, SD ver. s130_2.0.1)
I have problems when connecting via BLE with laptops...
Hi..
I want to implement a application ,i want to make a connection one central to multiple peripherals and to transfer the data from the one central to particular peripheral...
Hello All,
I am working on the NRF52810 with sdk 15.3 softdevice 6.1.1
I have added the 3 service like TX power, Battery Service, Immediate alert in my program.
I wanted...
We have possibly discovered a serious loophole that can brick a nRF9160 and will require JTAG to recover it.
We were loading a full set of certificates (CA, private, and...
Hi, I need your help.
I use NRF51822QFAA, SDK nRF51_SDK_9.0.0 and iPhone 11 ( IOS 13.2)
I use a project is ble_app_ancs_c at nRF51_SDK_9.0.0\examples\ble_peripheral\ble_app_ancs_c...
Hello,
We are experiencing an issue when putting the nRF52840 back to a low-power state after having had UART configured for double buffering. For context we are using nRF5...
Hello support Team,An unclear point came out when driving nRF52810 with Keil uVision5. I have a soft device(S112) write error. Can you help me with the following information...
Hello, Nordic!
I'm developing with nrf52840, s340, sdk 15.3.0
I made my app_error_fault_handler. It is very good for me.
I sometimes got an error. So I saw that log...
I didn't change the sample code. Why does the build fail?
1> Compiling ‘main.c’ 1> ../src/main.c:60:28: error: 'DT_ALIAS_LED0_GPIOS_PIN' undeclared here (not in a function...
Hi,
I am implementing a background DFU bootloader and uses the example from Vidar Berg ( https://devzone.nordicsemi.com/f/nordic-q-a/46994/background-dfu-application-source...
Hi,
I have just updated my app from SDK 15.2 to 15.3 (and the softdevice from 6.1.0 to 6.1.1).
Now nothing is working... I initializes a button with NRFX_GPIOTE and now...
Trying to set up attribute reporting I thought I had found a solution but was apparently wrong. My coordinator is sending an attribute reporting request with a minumum reporting...
Hello,
I'm using nRF52832 in a sensor PCB card, and I want it to have an antenna. Now I'm drawing the schematics of the PCB using KiCad, but there is one problem I can't...
Hello Nordic team,
Sorry for the ambiguous question. Let me know if you need further clarification about the question.
Currently we have a nRF52 based HID device....
Now that nrfutil has been ported to Python 3, I've been trying to get a DFU controller set up on a Raspberry Pi 3A running Raspbian Lite. I've built and installed the pc-ble...
