I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hi,
we are using nRF9160 with primary battery, so we are calculating the power consumption for sleep mode.
While doing the power calculation I have observed that, if 3...
Dear ,
I am using THINGY:91, FW: ncs v1.0.0 (#943 from joakimtoe : pca20035_to_master )
I moved to: https://github.com/NordicPlayground/fw-nrfconnect-nrf branch master...
I purchased a module that I encountered during startup. At first I programmed the module via the ST link v2.
Example: E: \ nRF5_SDK_11.0.0_89a8197 \ examples \ peripheral...
Hi,
I have just installed nRF Connect v3.2.0 on my Windows 10 x64 PC. I have an issue using the LTE Link Monitor app.
When I click on the Search networks button, I get...
I am able to program the nRF52832 but not all functionality is implemented.
I had previously programmed the device with a Nordic UART service and then tried to program...
Hi guy,
I am new to nRF52, I read some example code and I see this:
#define SPI1_CONFIG_SCK_PIN 2 #define SPI1_CONFIG_MOSI_PIN 30 #define SPI1_CONFIG_MISO_PIN 4 #define...
Hi there,
I'm currently working on a project in which I need to be able to deactivate Bluetooth advertising at the press of a button. I am using SDK 15.3 and have built...
I am using the database discovery module in my app (my code is based on the "HRS client" that is one of the SDK examples). I am able to discover multiple services (both custom...
To the kind attention of Nordic support team,
I have got legacy nRF24 gzll devices that are supposed to communicate with new nRF52 platform. Sometime it happens that nRF52...
Is board support available for Thingy91 "nRF9160_PCA20035" board in Segger Embedded Studio? I am not seeing "nRF9160_PCA20035" as a supported board under "ncs\zephyr\boards...
Hi,
In our project we want to use nRF52832 chip using HCI Command interface. We are trying to use Zephyr RTOS project for geting HCI interface through UART. We are using...
Hi, I using the 15.3 SDK.I want to get the peer's name by filtering Company ID(manu data).The Company ID is in the scan response packet, and peer's name is in the adv data...
Hello!
I would like to use an external antenna with my nrf9160dk to be able to attenuate the signal. But I am unsure about what is needed to make it work.
Is it enough...
Hi,
I have read through this tutorials on how to develop custom UUID, and I have implemented it successfully.
But I need to have 2 characteristics. I have basically duplicated...
Hello. I am trying to use TWI with mpu9250 sensor after System Off mode. But it is not working well. Do I need to do some preparation before going to System off mode? Where...
