Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
I'm using the ble_app_grs_freertos example. I'm trying to maximize its thru-put potential for Central devices which can support the high data rates. For this I've used the...
Hi, guys,
What I do:
Add freeRTOS into ble_app_hrs example project in SDK15.0
What matter I get:
When I set NRF_SDH_BLE_GATT_MAX_MTU_SIZE as 247, the device can not...
Hi Guys,
I am using Si7021 I2C temperature sensor and I want to read the temperature value using nrf52840-DK. I connected the sensor to the 27,26 pin.
I wanted to read...
DK version: nRF5_SDK_15.0.0_a53641a
Softdevice version: s132_nrf52_6.0.0_softdevice
I am using a Fanstel BT832X SOC, which has the SKY66112 PA, on a custom PCB. The...
Hello,
I am using UART to receive data on a nRF52840 DK.
I have written some code using the Serial Port Library.
I have attached snippets of the code dealing with the...
Hi,
I'm working on a tone library. I'm using timer2 and ppi channels to generate 50% pwm signal.
It's working fine.
Now i want to add another timer comparison ( timeout...
I am trying to see if there is a way I can generate a multi frequency audio signal without additional hardware. I am talking about something similar to DTMF. The audio wave...
Would you please tell me how to use the nrf52832 PWM interface to implement differential output to spkr?
Here is my PWM interface configuration code:
NRF_PWM0->PSEL...
I am working on a device which also needs to give audio feedback to the user.
The app on the mobile phone needs to send a wav (or similar) file (mono, speech) to the device...
hi, I am using nrf52832 development board for PWM and I want to play an audio (.wav) file using PWM, I am unable to play the audio clip using the PWM, and same audio file...
Hello,
I'm using SDK15.3 and trying to do a non-connectable advertising while connected.
For that I set my adv package as non-connectable, however, when I run the function...
Dear Nordic Team,
I have a BLE application that we developed on nRF52840 DK for S140 based SoC and this application is working fine on the DK Board.
Now we would like...
I am using IAR version 8.30.2 . When I try to build the example project is the nRF5_SDK_15.3.0_59ac345 for 802.15.4 for the wireless UART I get a build error:
wchar_t in...
When I start my nRF9160 modem (AT+CFUN=1) it can sit in CEREG mode 4 (unknown) for a couple of minutes, before it switches to 2 (searching) then 1 (registered).
Is that...
