I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hey, I am trying to sample from 10 analog sensors and stream the results via bluetooth. Since the nRF5 is on a board that only lets me access 5 Pins, I am using a 16:1 multiplexer...
Hi everyone!
At the begining I want to write what I'm using to make everything easier.
Device:
- NRF51822 xxAC ( This one ). - GSM module Simcom Sim 7000E ( This one...
I need to be able to upload my application to an nRF52832 through an ARM architecture Linux machine that I have remote access to. nrfjprog is not available for machines with...
Hello. I connected the Image transfer service (running on a nrf52840) to another nrf52840 running a modified BLE_NUS_C service.
However, a BLE packet won't be send out,...
Hello,
I have the following issue when trying to detect which GPIO triggered the interrupt:
For my low power application, I was trying to connect two switches to the...
Hi,
I'm in the process of designing my first prototype with the nRF9160 SiP. For the LTE antenna sub-circuit, I simply want to replicate (as much as possible) Nordic's reference...
Hello,
I am using custom nrf52832 PCB as central role. Also i have the peripheral with similar board . Peripheral communication is working properly if connected with the...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
Similar to WiFi and 802.15.4 where there are...
Hello,
Customer want to use
nRF51822 Bluetooth Smart Beacon Kit
with this requirements:
We need the most simple beacon. Additional sensors are not needed. Its main...
Hello Nordic team,
I'm using nrf52840 DK with SDK 15.3.0.
So I had an example sending data similarely to the ble_app_uart_c example that worked OK.
Basically I have...
Hello there!
We have a running prototype with an NRF24L01+ and ESB. But since it is not recommended for new designs, is there a successor for this setup?
Very low latency...
Hello everyone,
I have trying to store my serial data in nrf52832 SDK15.2 fs flash storage i need to appending data one by one in same file. i have using fds_record_update...
Hi,
I use nrf 52832 with pca10056 and i need to use float to filter my data with low pass filter, but with this device, it doesn't work. Do you know how can I use float...
I merged ble_app_uart with spi peripheral example, normal working like bluetooth connectivity, spi sending and receiving is working fine, but i want to transmit data received...
Hi
When I try and pair my App with my NRF52832 Nordic device, iOS responds with a popup 'Bluetooth Pairing Request'. If I tap 'Pair' here, the app connects, and all is well...
