I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
Hi,
I am trying to get the example spi slave working. I am using SDK 11.0 ( I will try again under the 12.0 SDK later today).
I've checked my spi master by running the master...
Hi,
I am trying to interface MCP2515 with nrf51-dk. MCP2515 talks over SPI, so I have taken SPI_master as my base code. I have used MCP with arduino, so I thought it would...
Hi DevZone,
I am Nordic beginner, I am using the Nordic SDK example code for my current project. Before using Nordic DK, I was using Arduino for this project.
There are...
I'm trying to enable the S140 softdevice on my nrf52840-PDK from NuttX. When I call sd_softdevice_enable(), it returns NRF_ERROR_INVALID_FLAGS, which is not one of the documented...
I hope, operating BLE 5.0 at low data rate will give us longer range in open space. So in an environment like a football field, where each player will have 5.0 operating devices...
Hello,
I tried to add the code of the bluetooth tutorial called "Bluetooth low energy Characteristics, a beginner's tutorial", with a code that measures the delay of two...
Hi
I am working on a design using an nRF24L01+ in a circuit also consisting of an ATMEGA microcontroller and a H-bridge motor driver driving a brushed DC motor. The whole...
hi all!
I would like to ask the DCDC and LDO two modes of choice. My product is a watch, it uses the cr2032 battery dropped to 2.5v by an external LDO to 52832 power supply...
Hi,
I am using nRF52832 development kit PCA10040 V1.2.1 2017:38. I am able to successfully run nRF_Examples\nRF5_SDK_14.2.0_17b948a\nRF5_SDK_14.2.0_17b948a\examples\ble_peripheral...
hi,
I am using PCA10040 v0.9.0 Nrf 51 DK.
In schematic I am not getting connection for programming connectio n .In sheet 4 of 5 at the USB Connector connection signal...
Hi,
I m trying to develop an linux-application running on node.js to communicate with a nrf52 device. I m using the noble-module ( noble ) and a usb bluetooth-dongle. ...
Hi,
Is it possible to connect nRF905 to nRF51822 via SPI, add ShockBurst code nRF51822 and then use alternately/simultaneously Sub GHz and Bluetooth communication?
I'm...
Is there nRF Connect or similar program that enables development of BLE applications for Windows 10 (using native BLE API - ideally universal windows platform)?
At a connection the call function app_error_fault_handler()
with parameters
m_error_data.fault_id = 0x01 m_error_data.pc = 0x14DBE m_error_data.error_info = 0x0
Is not...
I'm trying to configure UART functionality in my program, and in the event handler under APP_UART_DATA_READY I'm missing bytes that I should normally have received. The code...
