Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
Hi,
I have Raspberry PI 3 Model B Rev 1.2 running "Linux raspberrypi 4.9.41-v7+ #1023 SMP Tue Aug 8 16:00:15 BST 2017 armv7l GNU/Linux". Running BlueZ 5.43
I can connect...
Hi community,
Try use FDS to write some data before sleep.
Following example and test is work.
But I try write data before into
sd_power_system_off();
...
Firstly the develop environment.
Windows 10
KEIL as IDE
Device: nrf 51822 - sd s130 2.0.1 - SDK 12.1 nRF5_SDK_12.0.0_12f24da.zip
Use case:
We have 2 application mode...
Hello i am using segger studio i have recently purchased three nrf52dk speically for ble mesh..
i am trying to run examples of mesh alpha sdk that nordiac prvodies but it...
We were playing with renaming some of our test devices to use emoji and other multi-byte utf-8 characters. We have a custom characteristic that allows renaming (since iOS...
dear nordic employee:
I tried to download the project of the ble_app_hrs_c_central by keil(nrf52832)
but It show like the title
I know I should reset the IROM1 and...
Is there a way to get the supervision timeout counter from the peripheral side? I am currently working with nRF5X modules and starting with the nordic uart example from the...
I'm using nRF52832, soft device 2.0, SDK11 and as a central.
When it happens I'm scanning for peripheral to connect. Usually it's a peripheral advertises at very low rate...
Hello,
I'd like to work with my nrf52832 DK while traveling(sins I do that alot recently) and would like to download somehow all of the pages in nordic's info centre to...
It's clear an Android device can be a central, but I'm having a hard time finding any information indicating an Android device cab be a peripheral that an NRF52 could be programmed...
Our products should connect to a central device. This central device should also be a peripheral which a phone can connect to. Will this be possible? If not, could the phone...
Hi, I need some guidance or an more in-depth example on adding the necessary code to read/write on the UART1 using the serial module or something else. Everything I've tried...
I am working with nRFx modules and have a few questions about updating parameters. I started my project with an example and modified what I needed. However, I am not sure...
We create library for work with software serial, we use two modules gpiote, timer.
We have done software serial one instance but we need four (actually just for rx). We don...
