I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I want to transfer application over the air(OTA) to NRF51822, with using nrf-toolbox in android mobile so please tell me step by step procedure. and how to setup nrfDK to...
hello every,do you have the same question?
i delete the bsp relevant document,then i find that when i disconnect it from APP,it delay to Generate disconnect events. i use...
I'm trying out 6lowpan examples in the IoT SDK, and while everything works,
if I want to disconnect by running:
echo "disconnect 00:50:49:71:3b:44 1" > /sys/kernel/debug...
I have compiled the following list of error that are given by BLE Stack from the ble_app_gls code.
I would like to know what action needs to be taken on reception of all...
Hi everybody!
I want to do a connection between two BLEnano, one is the mater and the second the slave.
I have programmed the two BLEnano using the Arduino IDE and libraries;...
Hello,
I was wondering what is the best option/way to merge two functionalities which are developed in different examples of the nRF52 sdk12.2.
For instance, I would...
hi,
my device is nrf52832
i run my spi sd card driver fine in debug mode, but when i download it ( F8 ), it can not work!
so my question is what is the difference...
Hi,
I need to monitor radio channels and find the best one (with lower background noise) to use.
Is there any way to measure radio signal level in a particular frequency...
My problem: The run of my 1. DFU - Implementation delivers an error code after executing the line "err_code = ble_dfu_init(&m_dfus, &dfus_init);". For my opinion this is caused...
I'm trying to get a simple "Hello world" program to run on the Nordic ID Medea.
As soon as I start debugging I get the error "The bootstrap could not be loaded".
Any idea...
I follow this:
developer.nordicsemi.com/.../a00092.html
Creating an image file
The format of the firmware image that you use to update the device firmware depends on...
My problem: The run of my 1. DFU - Implementation delivers an error code after executing the line "err_code = ble_dfu_init(&m_dfus, &dfus_init);". For my opinion this is caused...
At the moment I am working on a project that uses the nRF52328 acting as both a peripheral and central to connect 3 separate devices intermittently. I am storing their bonding...
Hello,
I use SDK example nfc_text_record for pca10040 DK.
With aim to check memory area of the emulated tag I've modified example with next:
/* Set up NFC */
err_code...
