Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
Hi
I did not quit yet understand the Gazell Pairing library.
If an encrypted message is send, how do I add some payload to the acknowledgement.
And how will I be able...
Hi,when i set NRF_RADIO->MODE in RADIO_MODE_MODE_Nrf_1Mbit ,then use radio_tx_carrier(txpower_, mode_, CH_LOW); i got a picture with spectrum analyzer like this ! , when i...
Hi
I have been using the double buffer DFU for a while now, and it works reliably for me.
However, I am hitting the application size limit that can be handled by the double...
Hi,
We developed the app using the nRF Beacon App sample code.
I want to ask for a good application notes or some hints which I can use for developing.
* Is the API documentation...
The nRF51822 Product Specification says that "Maximum number of pins with 5 mA high drive is 3."
Does that mean that you can only configure 3 pins as high drive, or could...
I managed to upload my application OTA DFU when there was only the bootloader running. After my application is there, I can start DFU and my application runs thru reset_prepare...
Is there a firmware locking feature for either 51422/51822, or can you purchase OTP (one time programmable) versions?
Can you buy them mask programmed from Nordic?
I...
I want to get sensor data from arduino, with atleast 200 samples per second, but at present I am only getting around 20 samples per second. I went through forums and got to...
What is the source resistance for the GPIO pin when driven high and configured as following:
Output, Standard 0.5mA drive, No pullup, S0S1
Output, High 5mA drive...
Hi there! I added ANCS to my project which contains services nus, dis, dfus and two other custom services. Everything seems OK except device manager. I paired the device with...
Hello,
I would like to know whether the below PA can be interfaced with nRF51822?
For our application we need to increase the power of the BT. so I have selected the below...
Hi, I am now using hid mouse example to develop a project. On the nrf51822 side, connection\bond\data sent are all ok, then I need to test the project on phone side. In iOS...
Hello,
There is a problem of compile when I finished compile process on Keil as following. Is there any process I missed before I starting to develop nRF52 SDK? what I...
I'm using Windows driver 0.5.0 with a s130 BLE USB dongle.
If my application calls sd_rpc_open on init and sd_rpc_close before exiting, everything works fine.
Now, if...
