I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
I have looked over the entire site and can not figure out what is needed to change the Smart Beacon Kit firmware and uploaded it to the beacon.
Is there a way to recompile...
Hello ,
I'm working since few days on nRF51 dongle with SofDevice S310 and most things seem to be ok.
But when I follow the System OFF and wake-up sample supplyed on GitHub...
The v3 nrf51822 and nrf51422 power efficiency was improved.
What were the improvements? How much effect should we expect to see in various operating modes. System OFF,...
In the Nordic code at this github example
there is a reference to UICR.CLEN0 .
#define CODE_REGION_1_START 0x00020000 \\
/**< This field should correspond to the size...
What is the main difference between HW controlled TWI master driver and SW controlled TWI master driver?
What is their advantages and disadvantage?
Can they switch between...
I am creating four timers in my application using app_timer.c . All timers work except the timer with ID zero never triggers.( means first timer created does not work all...
I am really struggling to get my ADXL345 SPI code working. Everything works fine on a LPC1768 and all outputs are fine on the nRF51822 Eval board, but there is no activity...
Greetings,
SDK6.1 and Keil V5.12
I try to build the executable for Nordic GitHub project Timeslot Oberver example. I get an error that the handler SWI0_IRQHandler is multiple...
I created a app with s110 V7 and want to program the PCA10006 with this app.
To get thing working, I need to update the softdevice as well (beacon PCA10006 is shipped with...
I am trying to use the latest (s130_nrf51822_0.9.0-1.alpha) S130 and experiencing an issue which was not seen in previous version (s130_nrf51822_0.5.0-1.alpha), this is the...
Hello,
We're interested in measuring the precision of our external crystal, but don't have the equipment to measure off the crystal directly without affecting capacitive...
Hi,
I am trying to run nRFToolbox App, I imported the project to Android Studio but I get the following error when I attempt to run it:
Error:Execution failed for task...
I just switched over from SDK v6 to SDK v7.1 (installed via those Keil Packs). The UART has suddenly stopped working (via Segger USB COM port) and I can no longer see any...
Hi Nordic,
I used PIC32 for SPI Master and nRF51822 SPIS slave. I used shortcut for my spis in nRF51822 and I need to know the right time of acquiring the semaphore and...
