Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
Hi,
I am trying to run nRFToolbox App, I imported the project to Android Studio but I get the following error when I attempt to run it:
Error:Execution failed for task...
I just switched over from SDK v6 to SDK v7.1 (installed via those Keil Packs). The UART has suddenly stopped working (via Segger USB COM port) and I can no longer see any...
Hi Nordic,
I used PIC32 for SPI Master and nRF51822 SPIS slave. I used shortcut for my spis in nRF51822 and I need to know the right time of acquiring the semaphore and...
I have a 32 byte string to read and write using SD110. In the MCP I can read (using read long) the whole string without any problems. When I try to use write long, MCP times...
I'm getting started with the ble_app_hrs_s110_pca10028 (nRF51 PCA10028) example in the nRF51_SDK_7.1.0_372d17a_packs.zip SDK. See the tags for my hardware setup. I'm using...
Hi I'm working on a school project and I need to send data from an accelerometer to a phone I'm currently able to update "dummy" data from my nrf51822 to my phone after following...
Hello ,I want to scan the Bluetooth peripherals through one master application and want to display the Bluetooth peripheral names on serial window like what master control...
I am new to nrf51822.
I am trying to convert my Arduino code into NRF51822
I need something like this
currentMillis = micros(); //microseconds since the Arduino board...
Hi,
Without dissecting the provided Raspberry Pi Debian packages -- is there a list of the required Linux kernel modules and binaries required for the IoT Dev Kit example...
Hi there. I'm currently trying to run the BLE_APP_HRS example from IAR workbench on nRF51822-Evaluation-Kit.
We are very interested in using this chip in our upcomming products...
Hi All,
I noticed CSR has just released something called CSR mesh, please see: http://www.csr.com/news/pr/2014/csr-mesh , and a demo video: http://www.youtube.com/watch...
I'm renewing my search for a point-to-multipoint radio system, preferably based on the nRF51822. Basically, I need to be able to connect up to 32 (or more!) nodes to a master...
I am trying to implement a mesh protocol using the nRF24L01+ transceiver.
After reading the product specification, I have concluded that the Enhanced ShockBurst cannot...
I'm working on a wireless sensor network and was thinking about using nRF51822 as the primary SoC. For my network it would primarily be low power sensors talking to one another...
