Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
We've been working on a product that utilizes a NRF51822 chip as well as WS2812B NeoPixels. Since there have been numerous posts about it here we've decided to release our...
Due to limited resources we are looking for someone who can help us with making a custom profile.
You are preferably in the Stockholm area and have done this before.
The...
Hi,
I have a working project and want to use I2C 2 instead of UART 2. I have changed the .dts file:
/* &uart2 { status = "okay"; current-speed = <115200>; tx-pin = <29...
Just wanted to share my project of controlling the position of feedback servo motor with Nrf52840 by sending bluetooth commands using nordic toolbox
github.com/.../Feedback...
I used the mpu6050 sensor and did it according to 1.2 of this blog .
The driver of this sensor is in the ncs\zephyr\drivers\sensor\mpu6050 directory.Error after compiling...
SDK: NCS 1.4.0
board: nRF9160-DK
sample: lwm2m_client
# registration CoAP packet
In option enum, there is no "others". Where can I get this information?
I'm writing an application that transmits data over a mesh network of nRF52840 microcontrollers using OpenThread. I'd like the microcontrollers to prioritize sending MLE traffic...
I want to upgrade my application from v1.4.2 to v.1.5.1. but the Bluetooth init failed. So I tested with the scan_adv, which uses the same logic as my application. This also...
The device communicates okay with JLINK commander v7.00a although at the beginning it always says "Connecting to J-Link via USB...Out of sync , resynchronizing... J-Link communication...
Development Environment: icore7 laptop running Ubuntu 20.04.2 LTS.
Target: To build connectedhomeip sample application for arduino nano 33 ble board and check against laptop...
Hi,
We are building our project with nRF52811 and Segger Studio V5.34. (I have Ubuntu 1804 if it helps.)
We have certain variable configurations but would like the ability...
Hello Team,
My end goal is to send 0 to 600hz signal over Ble using NRF52832[ as explained below image].
So, for this, I have used this GitHub code
https://github...
Hello,
I am working an a product based on the NRF52832 and I need to trigger an interrupt when a capacitive button is pressed / proximity detected (BLE is peripheral and...
Good morning,
I'm starting to develop an application for the nRF52805 using ble_app_hrs_freertos as a base.
The modification I did are:
Ported from nRF52832 to nRF52805...
Hi,
I am developing a beacon scanner on NORDIC Thingy 52 using Nordic thingy52 SDK, Now I want to add NUS(Nordic UART service) in my code to send data to the client(ESP32...
I have successfully built the Dynamic Multi-protocols network with Thread and BLE, and used Raspberry Pi 3B + as Gateway Now I want to integrate more AI into the system, but...
