before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hello,
we are currently trying to create sensor networks with the nRF52840 Dongle . Our first RSSI measurements in the field show that the orientation (rotation) of the...
My Software as follows: nRF52832 DK(pca10040) nRF52 SDK15.0.0 mesh 2.1.1 SEGGER Embedded Studio 3.12
I want to transplant "examples\peripheral\pwm_library" to "examples...
Hi,
We have a firmware application using SDK 12.3 and Softdevice S132 V3.0.0 running on a nRF52 controller.The firmware is used pheriperial BLE device and provides a GATT...
I am working on ble_app_hids_keyboard example code. I downloaded the bin file in my eval kit and tried to connect the Nordic_keyboard device with my android device. Then,...
Looking at the "Pin assignments" section in nRF52840, I found that some GPIO pins are recommended for standard drive, low frequency I/O only. I am wondering whether there...
-SDK: 15.0
-S132
-nRF52832
-Segger studio
I'm trying to implement bonding/whitelisting to my project, which is a connectable beacon with a custom service. What I want...
My Software as follows: nRF52832 DK(pca10040) nRF52 SDK15.0.0 mesh 2.1.1 SEGGER Embedded Studio 3.12
I want to transplant " examples\peripheral\pwm_library " to " examples...
I need to change, on a time basis, the advertising packet :
Let's say for X seconds it has to work as a "iBeacon"
BLE_GAP_ADV_TYPE_NONCONNECTABLE_NONSCANNABLE_UNDIRECTED...
Hello,
We want to build Expiremental examples in BLE Peripheral.The Common issue which we have faced in bulding any of the Expiremental BLE Peripheral issue was the missing...
Hello. I am using the custom board (buttonless) of nRF 52840 to verify the services of DFU and NUS. After firmware rewriting with DFU, I confirmed that BLE communication with...
Hi,
Our Application software running in Micro is communicating with BLE over UART.
So in nutshell, we are using serialization to speak with soft device present on NRF52810...
Hi,
I'd like to have a second UART available, as the nRF51822 only has one and I'm wondering if there exists a UART software emulation example implemented already for this...
Hi!
I'm trying to add logging modules to my own libraries that I've created. I'm using SDK 14.3 with the nrf52832. I can enable logging for any of the SDK driver/libraries...
I am using nRF Connect to measure the power of the nRF52840 DK. But I don't know how to output the raw data out. Is there a way that we could get the data out from nRF connect...
