before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hello,
I am testing nRF7002DK board using nRF Connect SDK.
Does nRF7002 support Wi-Fi roaming such as 802.11k, 802.11r, 802.11v?
If it supports Wi-Fi roaming, please...
Hello,
I have a question regarding the sys_poweroff() function. In my device, there is a mode where the board (including the nRF52840 chip and GPIOs) remains powered, but...
Hi,
I am developing an application with the nRF5340 microcontroller.
I need to use the I2C module, but if I insert the CONFIG_I2C=y configuration in my prj.conf file,...
When disconnecting and connecting BLE, if the J-Link debugger is connected, BLE_EVT_DISCONNECTED in ble_evt_handler is executed, but if the debugger is not connected and the...
Hi Support Team,
Our product is based on nrf5340 and ncs V2.5.2. I developed a Windows application(based on .NET8.0 and Windows SDK11) to provision and configure the system...
Hi,
I have a custom nPM1100 borad and want to charge the battery. My schemetic shows here, I notice the battery cannot be charged. My shcemetic shows below:
I have confirmed...
Hi Support team,
I encountered some flash overflow errors when I enabled the MCUboot on nrf5340. Could I ask several questions?
My situations and requirements: 1. My project...
Dear Nordic Semiconductor Team,
We are very interested in your nRF7002DK development kit and are exploring its potential for use in an open-source IP camera project. Our...
Hi, I am using an two nrf5340 with hci_ipc enabled one acting as central and one as peripheral built on v2.9.0
The issue I am having is that the supervision timeout doesn...
We have a project with a device acting as a ble peripheral and a broadcast sink. First the ACL connection is set up and then it will scan for and sync to a broadcast with...
Hi,
With the attached code, the timer0_event_handler() is only called once - is there something else I need to do in the ISR or at initialisation-time to ensure that it...
Hi all! :)
I struggle to initialize GNSS when I don't have a connection with LTE. Examples that could be found on dev academy initializates GNNS after LTE has been initialized...
Hello,
I’m wondering if there is a way to separate CELL and Wi-Fi location data from GNSS location data in the Location library. Currently, we use nRF Cloud for location...
Hello.
I am trying to boot the nRF54L15DK from an external power source.
Referencing this page , I supplied 3.3V to P6, but the SoC could not boot.
The 'VDDM_nRF' through...
Hi! For several days I struggle with the issue (if it is an issue) of the nPM1300 battery current measurement. When the battery is charging the current value seens correct...
