Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
We've been working on a product that utilizes a NRF51822 chip as well as WS2812B NeoPixels. Since there have been numerous posts about it here we've decided to release our...
Goodmorning,
we are trying to update the firmware on a nRF24 development kit board (nRF2727) that was programmed with the PTX sample from your software development kit....
Is there a document comparing the differences between the softdevices for the 51832 ?
I have been looking at the data sheets, but its too much to grock on my own.
Thank...
SDK: 15.2 IDE: Keil SoftDevice: 6.1.1 Board: Custom Hello, I would like to synchronize an SAADC reading during a BLE transmit event. The power source to my board is a CR2032...
Hi,
I am developing an application for Thingy:91 in which I want to send data from the device to MQTT server. I am using 1.1.1 modem firmware and 1.2.0 ncs tag.
The whole...
I'm developing a product using an nRF52840 and an accelerometer.
I have created a Service with characteristic that sends accelerometer data over ble to the phone through...
I add this code in 'static void on_connect(ble_nus_t * p_nus, ble_evt_t const * p_ble_evt) ' on the sever.I got an err_code NRF_ERROR_INVALID_DATA. Softdevice is s132nrf52611...
Hi,
I have a custom board with the nRF52840.
Is it possible to customize the DFU to be able to update the firmware through other interfaces than BLE or USB/UART?
I have...
Hi, I'd like to set up cccd here, but test the error,
In the routine nRF5_SDK_15.3.0_59ac345 nRF5_SDK_15.3.0_59ac345.0_59ac345.s.ble_peripheral?ble_app_uart/pca10040-s132...
Hi.
I have a RAK5010 i use for iot application.
i recently moved from SDK 15.20 to sdk 16. I use the task manager to manage two tasks:
1. task to dump nrf logs
2....
From section 5.2.1.11 I can tell that the peak current with CPU, TX, DC/DC, HFXO running the power consumption would be 8.6n mA. However, I could not find one that included...
Hi, we are developing a home automation product that needs to support ZigBee. However, at the same time I would like the devices to be able to work with a simple non-mesh...
Hi,
I have a question about bit rates of spis slave (Fspis).What is the minimum bit rates of spis slave? nRF52832 need to communicate with a mcu that it only can work on...
I used a translator. Please understand even if the sentence is weird.
Hi, I used nrf52832 QFAA. (RAM : 64kB, Flash : 512kB)
nrf-intel-hex enabled us to check memory...
Hi,
i want to work with nrf9160 for cloud connectivity, can any one help me providing link for working nrf9160 sdk.suggest me how to build samples without any errors using...
Hi everyone,
I have a weird issue on connexion with my J-link while connecting to my chip. I'm using a NRF52810 which worked very well until now. When I try to connect to...