I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I am using the nrf52 Dk with nrf52832 chip and i want to write bulk data onto the dk and then when i read the dk from the mobile app nrf connect, i want to see the written...
Hi,
I am trying to integrate the DFU service into the ble_app_uart example. I am using NRF51822 with SDK 11. I was able to successfully run the ble_app_hrs with dfu. So...
Hi. I'm using 2x nRF52840 DK's + eero pro.
I've been noticing some stability/longevity issues with examples/thread/freertos_coap_server in nRF5SDKforThreadandZigbeev3209fade31...
Peer Manager in recent SDKs supports up to 20 peers but SoftDevice functions like sd_ble_gap_whitelist_set() and sd_ble_gap_device_identities_set() are able to handle up to...
Hi, I am trying to get BLE packages with the nRF52840 Development Kit without using Wireshark or other external app. Does anyone have any solution? Thanks in advance
I have followed this tutorial from this link but cannot get it work.
I have 3 loop. For the first loop of sending data it will have a delay about 1s and until 2 finish...
A%dBBCCDDEEAABBCCDDEEAABBCCDDEEAABBCCDDXX = 40bytes
1) In Termite:
Data is complete and in sequence when until 6 only.
A0BBCCDDEEAABBCCDDEEAABBCCDDEEAABBCCDDXX A1BBCCDDEEAABBCCDDEEAABBCCDDEEAABBCCDDXX...
I have 2 message order by sequence and between each of them have delay 2s. for Example
How should it work
A1BBCCDDEEAABBCCDDEEAABBCCDDEEAABBCCDDXX
Delay 2s
A2BBCCDDEEAABBCCDDEEAABBCCDDEEAABBCCDDXX...
Hello Nordic Support.
it was first time i tried to set up zigbee project based on 52840 and nRF5_SDK_for_Thread_and_Zigbee_v3.0.0_d310e71. and now i got question...
...
Hello,
I want to design my board using Raytac MDBT42Q-AT-UART module which has nRF52810 QFN SoC inside.
I need BOM with P/N and make of components which are used in...
Hello,
I am using nRF52840, SDK_16.0.0, S140 SoftDevice and Segger 4.16 for flashing the image. I am using ‘ble_app_blinky’.
1) I want to configure Advertisement channels...
Hello,
I am using nRF52840, SDK_16.0.0, S140 SoftDevice and Segger 4.16 for flashing the image.
Most of our devices are Peripherals. To control them, we will relay...
Hello everyone,
I already posted this on the Segger Forum, but rarely I get answers there, so I hope someone have a solution to this hellish problem! I have been happily...
Hi Sir,
I am working in nRF51 package for interfacing BLE. In general, I have doubts regarding BLE concepts.
1. How to calculate the maximum amount of BLE packets...
